SPARKY BR 9,6E Mode D'emploi page 8

VIII - Operation
lED WoRK AREA lIGHt
The drill has 3 LED lights (7) to illuminate the work
area and improve vision when drilling in areas with
insufficient light. To turn the LED lights on and off
depress the LED light switch (8).
REvERsING
The extreme position of lever (6) to the right
(viewed from the rear) is equivalent to anti-clock-
wise rotation, the extreme position to the left - to
clockwise rotation. When the ON/OFF switch (5)
is depressed lever (6) can not be actuated.
CAUtIoN: Reversing can be per-
formed only when the spindle is not rotating!
Drilling and tightening screws are performed with
lever in extreme position to the right. Removal of
screws is performed with lever in extreme position
to the left.
sWItCHING oN - sWItCHING off
Switching on: press ON/OFF switch (5).
Switching off: release ON/OFF switch (5).
The power tool is equipped with a brake. The spin-
dle stops rotating immediately after releasing the
switch lever.
smootH ElECtRoNIC RPm CoNtRol
Light pressure on ON/OFF trigger switch (5) re-
sults in low rotation speed, further pressing the
switch results in smooth increase of the rpm to
maximum upon reaching the extreme position.
toRQUE ADJUstmENt
By rotating the torque adjustment collar (2) behind
the chuck, it is possible to adjust the torque to
each of 15 settings.
The range of 15 torque settings allows better con-
trol when using the drill as a screwdriver as it pre-
vents over-tightening of the screws.
The numbers circling the collar are used to indi-
cate the level of torque. The larger the number on
the collar, the higher the torque. To select any of
the numbers, rotate the collar (2) until the desired
number aligns with the arrow head indicator on
the housing.

EN
pages-BR9,6-12E-15E.indd 8
All manuals and user guides at all-guides.com
sPEED sElECtoR sWItCH
(bR 2E, bR 5E)
The two-speed selector switch (3) enables you
to select the appropriate gear with the optimum
speed and torque to suit the application.
selector ensure the drill is not operating.
1. To select the low gear (low speed, high torque
2. To select the high gear (high speed, low torque
INsERtING AND REmovING bIts
ing we recommend removing the battery pack
out of the tool.
The drill is fitted with auto spindle lock which means
if you try and rotate the chuck by hand the spindle
of the drill will automatically lock. This means you
only need to grasp the chuck and rotate the chuck
housing to remove or fit accessories.
This drill is equipped with a keyless chuck, hence
a chuck key is not needed to secure a bit in the
drill. Always set the forward/reverse switch (6) to
the locked (neutral) position when installing and
removing bits.
1. Open the chuck jaws by firmly holding the
2. Ensure the accessory is fully inserted, so that
3. To firmly clamp the accessory in the chuck,
4. To remove the accessory, open the chuck jaws
CAUtIoN: When changing the gear
setting), push the gear selector (3) forward, to-
wards the chuck. The digit 1 on the switch will
be displayed.
setting), push the gear selector (3) back, away
from the chuck. The digit 2 on the switch will be
displayed.
CAUtIoN: To avoid unintentional start-
chuck housing and rotating the housing in an
anti-clockwise direction. Open the jaws suffi-
ciently so as to fit the desired accessory. 9
the jaws of the chuck grip onto the flat section
of the accessory.
grasp the chuck housing and rotate the chuck
housing in a clockwise direction. Ensure the bit
is retained firmly or damage to the chuck jaws
can result.
by rotating the housing in an anti-clockwise di-
rection.
bR 9,6E • bR 2E • bR 5E
22.8.2006 г. 14:07:17
DRIl
Drillin
▪ For
stee
▪ Ens
pos
▪ Beg
bit f
▪ Alw
▪ Sup
dist
▪ Use
▪ Use
wor
mate
Stee
Alum
Bras
cast
Drillin
▪ Use
▪ Ref
Drillin
▪ For
stee
▪ Ens
pos
▪ Beg
bit f
the
▪ Wh
woo
ged
hole
All dr
▪ Use
▪ Ma
pun
sCRE
Selec
numb
(2), ag
Insert
the s
drive