SPARKY BR 9,6E Mode D'emploi page 7

▪ Always use correct SPARKY battery pack (the
come one supplied with tool or a replacement pack
ormal exactly like it.) Never install any other battery
m. pack. It will ruin your tool and may create a haz-
attery ardous condition.
r near ▪ Charge battery packs only in SPARKY charg-
ers.
of any ▪ The battery pack utilizes nickel-cadmium cells.
venti- Cadmium is considered to be a toxic material.
Use an environmentally safe disposal unit at a
pack municipal waste disposal centre to dispose of a
r tem- damaged or worn out battery.
cate a
fIttING AND REmovING tHE
n and
bAttERy PACK
To remove the battery pack from the drill: firmly
n juice
press the battery release tabs (7) at either side of
the battery pack, and slide the battery backward
them
out of the tool.
nutes
Prior to inserting the battery pack ensure the
switch is in OFF position.
tion of
To install the battery pack: align rails on the tool
with the tabs on the battery pack and slide the bat-
rly:
tery pack on to the drill. Ensure the battery pack
ng in a
is sitting straight on the foot and correctly enter-
ing the runners. The battery should slide fully on
cation
to the drill foot until the battery pack "clicks" into
is ap-
position.
send
r local
bAttERy CHARGING
hen it
which
CON-
Follow charged after 1 hour, remove it from the charger
after this time.
if it is
old a
1. Align and slide the battery pack onto the charg-
a fire.
er until the battery pack latches "click" into posi-
k after
tion. Check that there is a firm connection be-
pack
tween the battery and the charger groove. 2
shed,
2. Plug in the charger to the wall outlet. The green
LED (12) will be lit, thus indicating presence of
supply voltage.
3. Press the charger switch (14). The red LED (13)
the
will glow, thus indicating beginning of charging,
ous-
and the green LED will turn off.
eturn
4. The battery charging time is approximately 1
hour. The red LED goes out when the charging
cycle is complete and the green light goes on.
RGER
5. Unplug the charger power cable from the mains
PtING
and then remove the battery from the charger.
tool.
Instruction manual
pages-BR9,6-12E-15E.indd 7
All manuals and user guides at all-guides.com
CAUtIoN: The battery will be fully
to obtAIN tHE bEst lIfE foR tHE
bAttERy
▪ Do not recharge battery after a short operation to
avoid decreasing operation time and battery ca-
pacity.
▪ Avoid conducting short charges. Make sure that
the battery is fully charged every time by allowing
the charger to complete its full charging cycle.
▪ When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
fire or explosion.
▪ Always unplug the charger when not in use and
store in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may
drop under 32ºF (0ºC) or exceed 104°F (40°C).
bAttERy INDICAtoR
The battery state is indicated by three LEDs (4). To
activate the battery indicator feature first release
the tool trigger switch (5) in case it is pressed, e.d.
the motor should not rotate. The three LEDs indi-
cate three levels of charge remaining in the bat-
tery - low, medium and high. When only one LED
remains glowing (low level) the battery should be
removed and placed into the charger.
VII - Know your product
Before using the power tool, familiarize yourself
with all the operating features and safety require-
ments.
Use the tool and accessories only for the applica-
tions intended. All other applications are expressly
ruled out.
1. Keyless chuck
2. Torque adjustment collar
3. Speed selector switch (BR 12E, BR 15E)
4. LED battery indicator
5. ON/OFF trigger switch
6. Forward/reverse switch
7. LED work area light
8. LED light switch
9. Rechargeable battery pack
10. Battery pack release tabs
11. Quick charger
12. Green LED
13. Red LED
14. Charger ON/OFF switch

EN
22.8.2006 г. 14:07:16