Télécharger Imprimer la page

SOUNDMASTER PL900 Mode D'emploi page 16

Publicité

Les langues disponibles

Les langues disponibles

Playing compact disc
Getting start
1.
Press the Function button (5/45) to select " CD " mode. The LCD display will show " busy " and then " no disc " if the CD
compartment is empty.
2.
Then press the CD tray open button (6) to open the CD tray (7).
3.
Place a CD with the printed side facing up inside the tray & then close the CD door.
4.
Focus search is performing and LCD display (3) will show " busy " and then display the total number of tracks & total
playing time.
Play / Pause mode
1.
Press the " CD Play/Pause
2.
To interrupt, press the " Play/Pause
Press again to resume normal playback.
Stop mode
1.
If " CD Stop
" button (19/38) is pressed during play or pause mode. It will go to stop mode and display total number of
track on the LCD display (2).
Skip mode (skip up
1.
During play or pause mode, if " Skip up
and then remain the play or pause mode.
2.
During play or pause mode, if " Skip down
the track.
Remark:-
Before pressing the " CD tray open " button (6) for changing disc
ensure the LCD resume to the original information.
-
The reaction time of the CD burner is longer than normal CD player due to the complicacy system.
-
Keep pressing with all difference function within a short time may cause mal-function of the system. Please re-start the
unit if this is happen.
-
The reading and playback time of CD-R(W) disc is various from brand to brand. It depends on the compatibility of the
used disc.
-
This device only design for normal compact disc format. Is not support any MP3/WMA format.
Repeat mode
Press the Repeat button (48) before or during playback, a single track or all the tracks can be played in difference mode as
follow:-
(1) repeat all track
Indicator
Play mode
on LCD display
Repeat all
Repeat 1
1
Off mode
--------------
CD disc programming
Up to 32 tacks can be programmed for CD playing. Before use, be sure the system is at stop mode before
programming:-
1.
Set in CD mode & stop the disc playback.
2.
Press the "Program" button (46), " Prog " indicator will appear on LCD display (3). Moreover, it will indicate program no.
(P-xx) and digits for track no. to be programmed.
3.
Select a desired track by pressing CD skip up
4.
Press the " Program " button (46) to store the trace into memory.
5.
Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6.
When all the desired tracks have been programmed, press CD " Play/Pause
assigned order.
7.
To cancel the programmed file, press "Stop" button (11/38) until " Prog " indicator is disappear on LCD display (3).
Remark:-
-
After program play and you can delete the programmed track in the order from the last one to the 1
programmed track start to played. Press stop button to set the unit in stop mode first, press " Clear " button at remote
control once, then press stop button to enter clear mode, press the Clear button again once by once. The programmed
track will delete one by one from the memory.
" button (13/36) to start playback, the first track will start playback.
" button (13/36) once, the playing time will be freeze on the LCD display (3).
/ skip down
" button (15/37) is pressed. It will go to next track and display the track no.
(2) repeat 1
(3) off mode
2
)
" button (15/37) is pressed. It will go back to the previous track and play
.
or down
buttons (15/37).
EN-3
Press the " CD stop " button (11/38) first and
" button (13/36) to play the disc in
st
one after the

Publicité

loading