Fein KBE 32 QW Mode D'emploi page 26

en
26
Do not use the magnetic core drill unit when the
coolinmg-lubricant system is defective. Each time
before operating, check for tightness against leaks and
for cracks in the hoses. Prevent liquids from entering or
penetrating electrical components.
Features
The restarting protection prevents the power tool from
automatically restarting if the power supply is inter-
rupted during operation. In this case, switch off the
power tool, check the power supply and then switch
the power tool on again.
PRCD personal protection switch (*) (see page 6)
The PRCD personal protection switch is specifically for
your protection; therefore, do not misuse it as on
On/Off switch.
If the PRCD personal protection switch is damaged, e.g.
due to contact with water, do not use it any more.
The PRCD personal protection switch is indispensable;
it is used for protection of the power tool operator
against electric shock. Under fault-free operation, the
control lamp of the PRCD personal protection switch
lights up.
Check the operability of the PRCD personal protection
switch before beginning to work:
1. Connect the plug of the PRCD personal protection
switch with the mains socket outlet.
2. Press the RESET–button. The indication light on the
PRCD personal protection switch lights up.
3. Disconnect the plug from the socket outlet. The indi-
cation light goes out.
4. Repeat steps 1. and 2.
5. Press the TEST–button; the indication light goes out.
If the indication light does not go out, do not run the
machine. In this case, contact the customer service.
6. Press the RESET–button; when the indication light
lights up, the machine can now be switched on.
Do not use the PRCD personal protection switch for
switching the power tool on and off.
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air.
Renew stickers and warning indications on the power
tool when aged and worn.
After several hours of operation, the play in the dove-
tail guide can increase. As a consequence, the drill
motor can glide alongside the dove-tail guide by itself.
In this case, retighten all set screws of the dove-tail
guide correspondingly so that the drilling motor can
easily be moved manually, yet does not glide by itself
(see page 12).
When the machine's power supply cord is damaged, it
must be replaced by the manufacturer or their repre-
sentative.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts your-
self:
Application tools, coolant container, holding fixture of
coolant container, swarf protector
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU- or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
The UKCA declaration is only valid for the Great
Britain market (England, Wales and Scotland) and only
for products intended for the Great Britain market.
After placing the product on the Great Britain market
the CE mark loses its mark validity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.