Publicité
Description
®
The Mitel
5610 Cordless Handset and IP DECT Stand provide SIP call
processing features on a cordless handset. The IP DECT stand supports up to
eight cordless handsets.
The IP DECT stand connects to the network through the PC port on a Mitel
5312, 5320, 5324, 5330, 5340, or 5360 IP Phone. The IP DECT stand extends
the SIP phone functionality from the communications platform to the handsets.
You can purchase additional handsets and chargers from the Mitel Customer
Service order desk.
The cordless handset has an indoor signal range of up to 50 meters (150 feet)
from the IP DECT stand and an outdoor range of up to 300 meters (900 feet).
Note that this range can be limited by concrete or metal barriers. To extend the
signal range, you can purchase an optional IP DECT Stand Repeater.
A
Figure
provides an overview of the completed installation.
What You Received
• 5610 Cordless Handset
• Handset Charging Cradle
• Power supply adapter for Charging Cradle. The power supply adapter kit
contains multiple, attachable, voltage connector plugs.
• IP DECT Stand
• Short CAT5 LAN cable
• Power supply adapter for IP DECT Stand. The power supply adapter kit
contains multiple, attachable, voltage connector plugs.
• Belt clip
• Belt clip removal tool
What You Require
• 3300 Internet Communications Platform (ICP) with MCD Release 4.0 SP1
or later software,
or
Mitel 5000 Communications Platform (CP) with v4.0 or later software
• Mitel 5312, 5320, 5324, 5330, 5340, or 5360 IP Phone.
IP DECT Stand Rear Panel Components (See Figure
#
Description
LAN Port: Connects to PC port on Mitel IP Phone via short Ethernet cable.
LAN LED:
OFF: IP DECT stand is not connected to LAN.
ON: IP DECT stand is connected to the LAN.
VOIP LED:
OFF: IP DECT stand is not connected to communications platform.
ON: IP DECT stand is connected to communications platform.
CALL LED
OFF: No call in progress.
ON: Call in progress.
POWER LED
OFF: Power is not connected.
ON: IP DECT stand is powered on.
POWER Input: Connects to the AC power adapter for IP DECT stand. Note that
there are two different power adapters. One is for the IP DECT stand; the other
for the handset charger. The connectors at the end of each adapter cord are dif-
ferent.
RESET button: Press to activate configuration changes or to enable handset
registration. The first handset automatically registers with the IP DECT Stand
after approximately 30 seconds. To register each additional handset on the
same IP DECT Stand, you must first reboot the stand by pressing the RESET
button on the rear panel of the stand.
You can also reset the stand configuration (including the admin user name and
password) to the default values using the this button. Press and hold the Reset
button for greater than 10 seconds to reset the stand.
Note that you cannot reset the stand while a call is being supported on a hand-
set that is registered to the stand.
Installation
Remove Existing Mounting Base
If the IP phone is installed on a mounting base, remove the base.
• Turn the IP Phone over.
• Disconnect the handset cord.
• Press the two plastic clips on both sides of the mounting base and remove
the base from the IP Phone.
Connect the Cables to the IP Phone
Connect the LAN cable into the LAN port on the back of the phone. Connect
the other end of the LAN cable to a LAN jack. See Figure
Connect the short CAT 5 LAN cable to the PC port on the back of the phone.
After you attach the IP Phone to the stand, you will connect the other end of
this cable to the LAN port on the rear panel of the stand.
Connect the handset to the back of the phone.
Connect the headset (optional) to the back of the phone.
NOTE: Some IP phones require an AC power adapter. Other IP Phone models
obtain power from the LAN. If Power Over LAN is available, it shall be
compliant with IEEE 802.3.af.
B
)
C
5
Publicité
