Technical Data - TOOLCRAFT 2436328 Mode D'emploi

8.3 Measuring relative angles
You can zero an angle (create a reference angle), and then take another measurement. The
new measurement will be relative to the reference angle.
1. Switch the power on and place the angle gauge onto a reference surface. Wait for the
values to stabilize.
2. Press ZERO to reset the angle to zero. A flashing "S" icon will appear on the display.
3. Hold the angle gauge steady until the "S" icon stops flashing.
4. When the "S" icon stops flashing, place the angle gauge onto another surface to measure
the relative angle.
5. Press ZERO to exit this mode.
8.4 Audible alert
■
Press to switch the alert ON/OFF.
■
An icon will indicate that alerts are active.
■
An alert will sound when the angle is ±1° from horizontal or vertical.
8.5 Hold
You can press and hold HOLD to freeze the display.
P :
RECONDITIONS
a
A measurement has been taken.
1. Press HOLD to freeze the display. The "H" icon will appear to indicate a hold is active.
2. Press HOLD to unfreeze the display.
9 Calibration
Important:
■
Calibration should be performed on a flat and smooth surface (no more than 5° tilt).
■
If the tilt is greater than 5°, "Erro" will appear on the display.
■
Do not tilt the angle during the calibration process.
■
Calibration will replace the factory calibrated setting. Make sure the calibrating sur-
face is level before calibrating.
P :
RECONDITIONS
a
Power is switched off.
a
Product is placed onto a level, flat, smooth surface.
1. Press and hold MODE and then press . The display will show "CAL 1".
2. While keeping the product still, press MODE.
à "CAL 1" will flash several times and then change to "CAL 2".
3. In the same location, rotate the angle gauge 180° and then press MODE.
à
You have calibrated the angle gauge.
10 Cleaning and care
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Clean the product with a dry, fibre-free cloth.
4
180°
11 Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accord-
ance with applicable regulatory guidelines.
Remove any inserted (rechargeable) batteries and dispose of them separately
from the product. You as the end user are required by law (Battery Ordinance) to
return all used (rechargeable) batteries. Disposing of them in the household
waste is prohibited.
Contaminated (rechargeable) batteries are labeled with this symbol to indicate
that disposal in the domestic waste is forbidden. The designations for the heavy
metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (re-
chargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your muni-
cipality, our stores or wherever (rechargeable) batteries are sold.
Before disposal, the exposed contacts of batteries must be fully covered with a
piece of adhesive tape to prevent short-circuits. Even if batteries are depleted,
the remaining energy can become dangerous in the event of a short-circuit
(bursting, severe heating, fire, explosion).
You thus fulfill your statutory obligations and contribute to the protection of the environment.

12 Technical data

Power supply ................................ 2x AAA 1.5 V batteries
Ingress protection.......................... IP54
Resolution...................................... 0.05°
Measurement range ...................... 0 to 360°
Accuracy........................................ ± 0.1° at 0° or 90°, ±0.2° at >0° or < 90°
Auto shut-off .................................. 3 mins
Operating temperature ................. 0 to +40 °C
Storage temperature ..................... -10 to +50 °C
Dimensions (W x H x D) (approx.)
Weight (approx.) ........................... 505 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2436328_V3_1221_dh_mh_en I3/O3
400 x 62.5 x 28 mm