Table des Matières
Publicité
39
FOR YOUR SAFETY READ BEFORE LIGHTIN G
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.
A.
This appliance has a pilot which is lit by a piezo-electric
spark gas ignition system Do not open the inner
compartment of the appliance an try light the pilot by
hand
B.
BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not light any appliance.
Do not touch any electric switch; do not use any
telephone in your building.
Immediately call your gas supplier from a neighbor's
telephone. Follow the gas suppliers' instructions.
GAS
KNOB
STOP! Read the safety information above on this label.
1.
2.
Set the thermostat to lowest setting (PILOT LIGHTING).
Turn the thermostat dial fully clockwise
3.
Push the gas control knob down slightly and turn clockwise
to OFF , see Figure A .
NOTE: Knob CANNOT be turned from PILOT to OFF
unless it is pushed down slightly. Do not force.
4.
Remove the outer burner door located below the gas control.
5.
Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow
label. If you don´t smell gas, go to next step.
6.
This unit is equipped with a push button pilot ignitor, which is
used to light the pilot. Locate the ignitor on the gas control.
7.
Turn gas control knob counterclockwise
see Figure B .
8.
The pilot can be located by looking through the glass view
port while pressing the piezo ignitor button. Look for a spark
at the pilot location.
TO TURN OFF GAS TO APPLIANCE
1.
Set thermostat Dial to the lowest setting (PILOT LIGHTING).
WARNING:
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
LIGHTING IN STRUCTIONS
IGNITOR
BUTTON
THERMOSTAT
DIAL
untit it stops.
in the safety information above on this
to PILOT ,
If you cannot reach your gas supplier, call the fire
department.
C.
Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D.
Do not use this appliance if any part has been under
water or if there has been an ignition of vapors
immediately call a qualified service technician to inspect
or replace the water heater. Water heaters subjected to
a flammable vapors ignition will show a discoloration on
the air intake grid and require replacement of the entire
water heater.
FIGURE "A"
FIGURE "B"
"OFF" POSITION
"PILOT" POSITION
TOP KNOB
9.
Once the pilot has been found, push the gas knob all the way
down. Immediately press the pilot ignitor button rapidly (4) to
(5) times. If the pilot will not light, repeat steps (3) through (9).
10.
Continue to hold the gas control knob down for about one
(I) minute after the pilot is lit. Release the gas control knob and
it will pop back up . Pilot should remain lit. If it goes out, repeat
steps (3) through (9). It may take several minutes for air to
clear the lines before the pilot will light.
If knob does not pop up when released, stop and
immediately call your service technician or gas supplier
If the pilot will not stay lit after several tries, turn the gas
control knob clockwise to "OFF" and call your service
technician or gas supplier, see Figure "A".
11.
Once the pilot flame is established replace the outer
burner door.
12.
At an arm's length away, turn gas control knob
counterclockwise to "ON", see Figure "C".
13.
To insure that the Burner is ignited look for an orange glow
from the burner thru the pilot viewing window.
14.
Set thermostat to desired setting.
DANGER:
Hotter water Increases the risk of scald Injury.
Consult the instruction manual before changing temperature.
2.
Push gas control knob down slightly and turn clockwise
to "OFF", see Figure "A". Do not force
FIGURE "C"
"ON" POSITION
Publicité
Table des Matières
