Hard Floor Cleaning - Thomas HYGIENE t2 Mode D'emploi

We recommend THOMAS ProTex original cleaning
detergent for cleaning carpets.
See label on the cleaning agent bottle for application and
dosage.
Use hand warm water (max. 30°C).
Connect up suction hose and fit telescopic suction tube.
Fit carpet spray nozzle, spraying hose to the suction tube with
fast coupling and move upwards and place on the shut-out
valve and lock by turning. Afterwards fasten the spray hose
by means of the two tube clips on the suction tube.
Pull out the mains power supply plug and cable from the
appliance and connect up.
Switch on the appliance and set for maximum suction power. Switch
on pump. Control lamp comes on.
Spray extraction system
• Spray the cleaning agent deep into the carpet under pressure
• This releases the dirt and washes out deep down into the fibres
• Suck up the dirty water at full power and straighten up the
carpet pile again.
This should be always carried out in a single operation.
Sucking up and
Absaugen und
straightening
Aufrichten
Releasing and washing out Lösen und Auswaschen
Press the lever on the shut-off valve (24) until the cleaning agent
escapes. Draw the nozzle straight over the carpet and press
it down at the same time. The spraying volume can be set as
required by means of the setting wheel on the handle. Release
the valve lever to stop spraying at the end of one run or when
stopping work. When the sprayed liquid has been sucked up,
lift the nozzle and begin a new run but overlap slightly. In this
way you can clean the entire area section by section.
Should there still be traces of liquid remaining on the cleaned
areas this liquid can be sucked up without having to spray
again.
Make sure that the mechanical suction controller (25) is
completely closed.
In the case of very stubborn dirt you can apply the cleaning
agent while moving the carpet spraying nozzle forwards. The
same treatment can also be applied by just putting the pump
into operation.
Ensure that you do not spread too much liquid over the carpeting
since this may cause waves or bumps in the carpet. However, these
will disappear again after being allowed to dry for a longer period
of time.
Working direction
Arbeitsrichtung
Spraying
Einsprühen
Empty the waste water tank after you have used up all the
cleaning agent from the fresh water tank to prevent the
appliance being switched off automatically.
Should you not observe the above-mentioned instructions the
float will automatically switch off the appliance as soon as the
waste water tank is full. (You will clearly hear the motor be
running at a higher speed.)
Switch off appliance, disconnect the mains plug and empty the
waste water tank.

hard floor cleaning

Drop the hard floor adapter over
the carpet spraying nozzle and
lock by means of the slide.
By using this system you can clean
and dry your hard floor coverings
such as tiles, stone floors and PVC
at one and the same time.
See carpet cleaning for
procedure.
We recommend THOMAS ProFloor cleaning agent for hard
floor cleaning.
Maintenance cleaning of smooth floor coverings such
as linoleum, PVC, tiles, polished stone floors and lami-
nate floors with the microfibre pad
– General instructions:
Proper care of floors is an essential component
under our terms of guarantee!
To be observed without fail are the special care
instructions of the manufacturer of the floor
coverings.
The surface protection finish can be damaged or destroyed when
cleaning and using aggressive universal cleaners.
Maintenance cleaning is to be carried out by dust suction or by wiping
over with moist cloth.
Atomised moisturisation means: The floor must be completely dry
after 3-5 minutes. This method is only to be used on laminate floors
when recommended by manufacturer.
Wash the microfibre pad before using it for the first time to remove
any possible residue given as a result of the production process.
We recommend THOMAS ProFloor cleaning agent for main-
tenance cleaning of smooth floor coverings such as linoleum, PVC,
tiles, polished stone floors and laminate floors.
Dismantling/assembling:
1.
2.
6.
2.
3.
1.
5.
4.
19