Steering Wheel (8); Tow Bar (9); Quick-Release Supports (1:N); Tyre Pressure - Stiga Park 4WD Serie Manuel D'utilisation

EN
used).
• 4 Screws (7:K).
• 4 Shoulder washers (7:L).
• 4 Split lock washer (7:R).
2. Position the seat on the seat bracket
mounting.
3. Put the shoulder washers (7:L) on the screws
(7:K), complete with washers (7:R).
4. Insert the screws, complete with shoulder
washers, in the slots in the seat bracket and
the holes in the seat plate. Screw the seat
into place.
Tightening torque: 9±1.7 Nm.
Tightening the screws to a torque over
9±1.7 Nm, will damaged the seat.
5. Check that the seat moves easily in the slots
in the bracket.
The seat can be folded. If the machine is parked
outside where it is exposed to rain, fold the seat
forward to protect the seat cushion from getting
wet.
5.5

STEERING WHEEL (8)

In order to minimise axial play in the steering co-
lumn, place the 0.5-mm and/or 1-mm shim/s (3:C;
3:B) on the steering column between the sleeves,
pos. (8:A) as follows:
1. Install the sleeve (8:B) on the steering co-
lumn and secure in place by inserting one
of the pins (8:C) by approximately 1/3 of its
length.
2. Pull the sleeve and steering column upwards.
3. Check that the 0.5-mm shim, the 1.0-mm
shim (or both) can be inserted into the gap
which is created in point (8:A).. The shim/s
must not be forced in, as there must be a
little axial play.
4. Remove the pin (8:C) using a pin punch (8:D)
and remove the sleeve.
5. Install the shim/s as indicated in point 3
above.
6. Install the sleeve on the steering column and
secure by inserting both pins completely.
Block the steering column.
5.6

TOW BAR (9)

Install the tow bar (9:B) on the rear of the machine.
Use the screws and nuts (9:A; 9:C).
Tightening torque: 22 Nm.
12
ENGLISH
(Translation of the Original Instructions)
5.7

QUICK-RELEASE SUPPORTS (1:N)

The quick-release supports and relative installa-
tion instructions are supplied in a separate box
inside the machine packaging.
Install the quick-release supports on the machi-
ne's front axles.
5.8

TYRE PRESSURE

For the tyre pressure, please refer to chap. "0
TECHNICAL DATA TABLE".
5.9

ATTACHMENTS

For installation of attachment, see the installation
guide accompanying each attachment.
Note: In this case the cutting means as-
sembly is considered an attachment.
6.1 MECHANICAL ATTACHMENT LIFT PE-
DAL (10:C)
The control lever (10:C1) is used to take the
accessories from the operating position to the
transport position.
• Transport position: press the pedal right down
then lift your foot off: the pedal stays down.
• Working position: press and slowly release the
pedal.
Do not attempt to switch to the tran-
sport position while the hooked-up
attachment is in operation. This will de-
stroy the drive belt.
6.2

PARKING BRAKE PEDAL (10:B)

Never press the pedal while driving.
There is a risk of overheating the power
transmission.
The pedal (10:B) has the following positions:
Released: Traction is engaged. The
parking brake is not activated.
Pressed to halfway: Forward drive
disengaged. The parking brake is not
activated.
Pressed right down. Drive disengaged. The
parking brake is fully activated but not locked. This
position is also used as an emergency brake.

6 CONTROLS