Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Getting ready for operation
a) Remove and replace compartment cover
Important
•
Always replace the cover after inserting the SD card or pairing the camera
•
Take care not to damage the speaker wires when removing the compartment cover.
•
Make sure the rubber gasket is properly seated in the groove before replacing the compartment
cover.
1. Release the two compartment cover screws to remove the cover.
b) Install / replace microSD card
Important
•
The microSD card should be formatted using the FAT32 file system. Refer to your computer
software instructions for information about how to do this.
1. Insert the microSD card into slot, it will "click" into place.
2. Remove using the tip of your finger to press down until it "clicks", then release to eject.
Pair the device with the app before replacing the compartment cover.
Turning on and pairing
a) Power on
•
The camera will turn on when connected to the power supply.
•
It will take a few moments for the camera to load up.
b) Pairing
•
If the camera is has not been paired with the app:
- You will hear two beeps.
- The beeps will continue at 15 second intervals until the camera has been paired.
- If needed, see section "Reset the camera" to enter pairing mode.
•
If the camera is already paired with the app: The camera will beep once and function as usual.
Reset the camera
Perform a reset if the camera is not functioning correctly or you would like to enter pairing mode.
Important
•
Any previous connections will be lost after resetting.
•
If previously paired with an app, you must also "Remove Device" via the app after the device
has been reset. Refer to the app operating instructions for information about how to "Remove
Device".
1. Press and hold the Reset button 4-5 seconds until you hear a long beep, then wait a few moments for
the system to restart.
2. Repeat the pairing process after you hear the startup tone and the camera enters pairing mode. See
section "Operation B) Pairing".
Application connection tips
Important
•
This device is only compatible with 2.4 GHz networks.
•
Enter the exact "Wi-Fi Name" (case sensitive).
•
Have the password for your Wi-Fi router ready.
•
Connect the mobile phone or tablet to same Wi-Fi network the camera will connect to.
Pairing: "Add device" → "Video Surveillance" → "Smart Camera"
Operation
a) Low light recording
If the camera is placed behind glass, glare from infrared LED lights may overexpose the image.
The device is equipped with a light sensor that automatically triggers "night vision" when ambient
light falls below a certain level.
The recorded image will be in black and white.
b) Motion detection
•
With a microSD card inserted:
- 15 second clips will be saved until the SD card is full.
- You will receive notifications on your phone
•
If no microSD is inserted, or if the SD card is full:
- No clips will be saved.
- You will receive notifications on your phone, then open the app to view live video (with option to save
to mobile device memory).
Care and cleaning
Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they
can cause damage to the housing and malfunctioning.
•
Disconnect from the power supply before cleaning.
•
Clean the product with a fibre-free cloth, slightly dampen if needed.
•
Do not apply excessive force to the solar panels during the cleaning process.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product con-
forms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Enter the product item number in the search box. You can then download the EU declaration of
conformity in the available languages.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
a) General
Input voltage / current ........................... 5 V/DC, 1 A max.
Power consumption .............................. <5 W
Audio .................................................... 2-way (microphone and speaker)
Resolution ............................................. HD 1920 x 1080 p, SD 640 x 360 p
Frames per second ............................... 15 fps
Recording ............................................. Continuous loop (motion activated)
File record size ..................................... 15 s (in motion detection mode)
Until SD card full (manual recording)
Video compression ............................... H.264
Focal length .......................................... 3.6 mm
Field of view .......................................... 90° horizontal, 80° vertical
Storage ................................................. MicroSD class 10 (max 32 GB)
MicroSD file system .............................. FAT32, exFAT
Ingress protection ................................. IP65
Power cable .......................................... 2.3 m (USB-A male)
Operating / storage conditions .............. -20 to +40 °C
Dimensions (Ø x H) .............................. 70 x 149 mm (camera)
Weight .................................................. 223 g (camera)
b) Motion detection
IR LED .................................................. max. 15 m range
<10 lux trigger LED
Motion detection ................................... PIR (Passive Infrared)
PIR detection angle .............................. 110°
Detection range .................................... 20 m
c) Wireless connectivity
Bandwidth ............................................. Min. 2 Mbps upload speed
WLAN technology ................................. IEEE 802.11 b/g/n, 2.4 GHz
Frequency ............................................. 2.412 - 2.462 GHz
Transmission power.............................. 3 dBm
Transmission distance .......................... max. 25 m (line of sight)
d) Adaptor
Input...................................................... 100 - 240 V/AC, 50/60 Hz, 0.2 A
Output ................................................... 5 V/DC, 1 A
e) Application software
Supported OS ....................................... Android 4.2 (or higher),
iOS 9.0 (or higher)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
*2267528_v2_1221_02_dm_mh_en
Publicité
Table des Matières
