Technical Data - Sygonix 1925816 Mode D'emploi

Operation
a) Turn Camera On / Manual Video Record
The camera can be operated while charging.
• Insert a compatible MicroSD card into the Micro-SD card slot (4).
• Press and hold the Power / REC (1) button for approximately 2 seconds.
• LED indicators (3): Blue flashes 3x then turns off.
• The camera will turn on and recording will begin.
b) Turn Camera Off / Save Recorded Video
• Press and hold the Power / REC (1) button for approximately 2 seconds.
• LED indicators (3): Blue and red flash then turns off.
• Any recorded video will be saved onto the MicroSD card and the camera will turn off.
c) Motion Detection Video Record
The built in PIR sensor responds to temperature changes within the detection range
e.g. humans or animals whose temperatures differ from the ambient temperature.
The PIR sensor may not work correctly behind glass. The detection angle is 45º
(horizontal and vertical) and the detection distance is 5 m. For best detection,
position the sensor so the object does not walk directly towards it, but crosses from
left to right or vice versa.
Motion detection (2) for approximately 2 seconds.
• Press and hold
• LED indicators (3): Blue flashes 1x then turns off. Red flashes 3x and stays on.
• The camera will now record when motion is detected.
d) Low Light Recording
When ambient light levels drop below 10 lux, the camera will automatically switch to low light
recording mode. The recorded video will be in black and white.
e) Video Playback
• You can play back recorded video clips the following two ways:
1
2
• The camera will appear as a removable disk drive on your computer.
• Open the drive and enter the "DCIM" folder to access saved videos. If needed, copy videos
to your computer for backup purposes.
• Select a "MOVIxxx.avi" video file for playback.
Camera Stand
The adhesive base (9) may leave marks or damage sensitive surfaces. For
maximum adhesion, make sure the contact area is smooth, dry and free from debris.
Do not adhere the stand to a vertical or inverted (upside down) surface. There is a
risk that the camera may fall causing damage or injury.
Do not adjust the stand with the camera attached.
• Remove the adhesive backing from the base (9) and attach to a suitable surface.
• When making adjustments to the stand, always hold the base of the stand against the surface
to prevent the adhesive from peeling off.
• Attach the camera to the magnetic platform (8).
Reset the Camera
• Use the supplied reset pin or similar tool (like a paperclip) to reset
your camera in case of a malfunction.
• Gently insert into the hole marked R (6) and gently press. You
should feel a small "click".
• The camera will return to factory default settings.
LED Status Indicators
Status
Charging
Fully charged
Power off
Manual recording
Motion detection recording
Motion detection standby mode
Disk is being read
Power on (no MicroSD card inserted)
Reset
Low power
- Remove the MicroSD card and insert it
into the card reader.
- Connect the card reader to an available
USB port on your computer.
- Connect your device to a computer
using the USB cable.
- Turn the device on by pressing and
holding the Power / REC (1) button
for approximately 2 seconds.
LED Activity
Steady yellow
Yellow turns off
Blue and red flash then turns off
Blue flashes 3x then turns off
Blue flashes 1x then turns off.
Red flashes 3x and stays on
Steady red
Blue flashes continuously
Blue flashes 10x and the camera turns off
All lights turn off
Red flashes 10x and camera turns off
Care and Cleaning
• Disconnect the product from the USB port before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines. You thus fulfill your statutory obligations and
contribute to the protection of the environment.

Technical Data

Input voltage / current ................... 5 V/DC, 1 A via micro USB
Rechargeable battery ................... Li-Po, 3.7 V 1000 mAh
Battery recharge time ................... Approx. 2 hours
Runtime ........................................ Approx. 6 hr (day light), approx. 3 hr (low light)
Power consumption ...................... Day light: 130 mA, low light: 330 mA, standby: 12 uA
Motion detection ........................... PIR sensor, 45º detection angle, 5 m detection distance,
< 10 lux to activate, max. 1 year standby time
Low light recording distance ......... Approx. 5 m
Continuous recording ................... Yes (via setting)
Video audio record ....................... Yes (via setting)
Time and date video overlay ........ yes (via setting)
Video record frequency ................ 50 Hz, 60 Hz (via setting)
Camera lens ................................. 110º (viewing angle), 2.4 mm (focal length)
Video format ................................. AVI
Video segments ............................ 2 min / file (normal), 1 min / file (motion detection mode)
Video resolution ............................ VGA (640 x 480), HD 720 p (1280 x 720), Interpolated HD
1080 p (1920 x 1080)
Video file size ............................... HD 720 p (98 MB), Interpolated HD 1080 p (219 MB), VGA
(147 MB) *Averages for 1 min segments. Values will vary
depending on recording conditions e.g. light levels (lux).
Video frame rate ........................... 30 fps
Memory type ................................. MicroSD, 8 to 32 GB (class 4-10)
MicroSD card format ..................... FAT32
Camera recording angle ............... 110° (vertical / horizontal)
System Requirements .................. Windows
Operating / storage conditions ...... 0 to +50 ºC, 0 – 85 % RH
Dimensions (H x W x D) ............... 33 x 33 x 36 mm
Weight .......................................... 51 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
7 (or above)
®
*1925816_v2_0919_02_dh_m_en