Publicité
M o d e l l s p o r t
damage the speed controller. Never disconnect the device from the motor or battery during
operation. Use high-quality plug systems with suficient load capacity. Avoid strong bending or
tensile stress on the connecting cables. After termination of light or driving operation, disconnect
the battery to prevent deep discharge of the battery. This would cause permanent damage. For
the BEC version of the controller, check that the BEC power of the device is suficient for the servos
used. Speed controllers should be installed as far away as possible from other remote control com-
ponents. We recommend carrying out a range test before operation. We recommend regular
checking of the controller for function and externally visible damage. Do not continue operating
the controller if you notice any damage. The connection cables must not be extended. This can
lead to unwanted malfunctions. Despite existing safety and protective devices of the device,
damage may occur which is not covered by warranty. The warranty also expires if changes are
made to the device.
Important information:
The receiver system is powered by the built-in BEC system of the controller.
For commissioning, always move the throttle stick to the „Motor off" position and switch on the
transmitter. Only then connect the battery. To switch off always disconnect the connection batte-
ry motor controller, irst then turn off the transmitter. During the functional test, move the servos of
the rudders to neutral position with the remote control (stick and trimming lever on the transmitter
to the middle position). Please make sure to leave the throttle stick in the lowest position so that
the engine does not start. For all work on to the parts of the remote control, motor or controller,
follow the instructions supplied with the units. Also read the instructions of the battery and the
charger carefully before commissioning. Check the engine mounting bolts in the fuselage regular-
ly for tightness.
W A R R A N T Y
Our articles are equipped with the legally required 24 months warranty. Should you wish to assert
a justiied warranty claim, always contact your dealer, who is responsible for the warranty and the
processing. During this time, any functional defects that may occur, as well as manufacturing or
other problems, will be rectiied.
Material defects corrected by us free of charge. Further claims, e.g. for consequential damages,
are excluded.
The transport to us must be free, the return transport to you is also free. Freight collect shipments
cannot be accepted. We cannot accept liability for transport damage and loss of your consign-
ment. We recommend appropriate insurance.
To process your warranty claims, the following requirements must be met:
• Attach the proof of purchase (receipt) to your shipment.
• The units have been operated in accordance with the operating instructions.
• Only recommended power sources and original robbe accessories have been used.
• There is no moisture damage, external interference, reverse polarity, overloading or mechanical
damage.
• Attach relevant information for inding the fault or defect.
I N S T R U C T I O N S A N D U S E R M A N U A L
Robbe Modellsport cannot monitor compliance with the assembly and operating instructions
or the conditions and methods for installation, operation, use and maintenance of the model
components.Therefore, we accept no liability for losses, damage or costs arising from or in any
way connected with incorrect use and operation.To the extent permitted by law, the obligation
to pay damages, irrespective of the legal grounds, shall be limited directly to the invoice value of
the claims arising from the event causing the damage.
Ground-based models are usually covered by personal liability insurance. Additional insurance or
extension is required for aircraft models. Check your insurance policy (private liability) and take
out suitable insurance if necessary.
www.modellmarkt24.ch
www.modellmarkt24.ch
D I S C L A I M E R
I N S U R A N C E
C O N F O R M I T Y
Robbe Modellsport hereby declares that this device complies with the es-
sential requirements and other relevant regulations of the corresponding
CE directives. The original declaration of conformity can be found on the
Internet at www.robbe.com, in the detailed product view of the respec-
tive device description or on request. This product can be operated in all
EU countries.
D I S P O S A L
This symbol means that small electrical and electronic devices must be
disposed of at the end of their useful life, separated from the household
refuse. Dispose of the device at your local municipal collection point or
recycling centre. This applies to all countries of the European Union and
other European countries with a separate collection system.
M o d e l l s p o r t
Made in China
+14
5
Publicité
