Safety Information; Intended Use - 3M DBI-SALA Mobi-Lok 2200094 Manuel D'instruction Pour L'utilisateur

SAFETY INFORMATION

EN
Please read, understand, and follow all safety information contained in these instructions prior to the use of this Vacuum Anchorage
System. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Vacuum Anchorage System is intended for use as part of a complete personal fall protection system.
Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not
described in the User Instructions, is not approved by 3M and could result in serious injury or death.
This system is only to be used by trained users in workplace applications.
!
WARNING
This Vacuum Anchorage System is part of a personal fall protection system. It is expected that all users be fully trained in the safe installation
and operation of their personal fall protection system. Misuse of this system could result in serious injury or death. For proper selection,
operation, installation, maintenance, and service, refer to these User Instructions and all manufacturer recommendations, see your supervisor, or
contact 3M Technical Service.
• To reduce the risks associated with working with a Vacuum Anchorage System which, if not avoided, could result in serious
injury or death:
- Inspect the system before each use and at least monthly. Inspect in accordance with the User Instructions.
- Ensure the system is inspected/recertified after any fall event and at least annually by an authorized service technician.
- If inspection reveals an unsafe or defective condition in a component of the system, remove the system from service and return to an
authorized service center.
- This system has built in audible alarms. Only use the system if alarms are functioning and you are capable of hearing them.
- Always connect to the designated fall protection anchorage connection point.
- The system must only be installed on the specified surfaces and with the methods detailed in the User Instructions. Installations and use
outside the scope of this instruction must be approved by 3M Fall Protection.
- The surface structure to which the system is attached must be able to sustain the static loads specified for this system in the orientations
permitted in the User Instructions.
- Never change batteries in a potentially explosive environment.
- Only replace batteries with those specified in the User Instructions.
- Do not puncture, modify, or alter the cylinder or compressed air line in any way. This can result in the hazardous and uncontrolled release
of pressurized gas.
- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet
the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements.
Always consult a Competent or Qualified Person before using these systems.
• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:
- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with
your doctor if you have any questions regarding your ability to use this equipment.
- Never exceed allowable capacity of your fall protection equipment.
- Never exceed maximum free fall distance of your fall protection equipment.
- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or
suitability of the equipment for your application. Contact 3M Technical Services with any questions.
- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections.
Consult 3M prior to using this equipment in combination with components or subsystems other than those described in the User
Instructions.
- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures,
chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or your the fall protection
equipment.
- Use Arc Flash or Hot Works devices when working in high heat environments.
- Avoid surfaces and objects that can damage the user or equipment.
- Ensure there is adequate fall clearance when working at height.
- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.
- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.
- If a fall incident occurs, immediately seek medical attention for the fallen worker for the worker who has fallen.
- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.
- Minimize swing falls by working as directly below the anchorage point as possible.
- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an
unintended fall hazard.
- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.
6
SIT 5908431 A