Overhead Rigging - BEGLEC JBSYSTEMS Light LOUNGE LASER DMX Mode D'emploi

ENGLISH
Important: Never look directly into the light source! Don't use the effect in the presence of persons suffering
from epilepsy.
LASER SAFETY INSTRUCTIONS:
 According to the EN/IEC 60825-1 ED2, 2007-03 regulations, this laser falls under the classification 3B.
Direct eye exposure can be dangerous.
DANGER: LASER RADIATION !
Avoid direct eye exposure! Laser radiation can cause eye damage
and/or skin damage. All protective measures for a safe operation of
this laser must be applied.
 This product is a so-called show laser, emitting radiation with a wavelength spectrum between 400 and
700 nm and producing lighting effects for shows.
 Due to the construction of this laser, the beam is moved so fast, that it can only hit the eye very short. This
is why the use of this laser for a Laser-Light-Show can
be regarded as save.
 Never direct the laser beam to people or animals and
never leave this device running unattended.
 This laser may only be used for shows. The operation
of a class 3B show laser is only allowed if the
operation is controlled by a skilled and well-trained
operator.
 Depending on the classification, operating a laser
product can produce laser radiation that may cause
permanent eye damage and/or skin damage. The legal instructions for using a laser product vary from
country to country. The user must always inform himself on the legal instructions valid in his country and
apply them to his situation.
Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect installations and
unskilled operation!
DESCRIPTION:
1. MAINS INPUT: with IEC socket and integrated fuse holder and switch, connect the supplied mains
cable here.
2. KEY ACTIVATED SWITCH: used to switch the lasers on/off. Use the keys to make sure only a skilled
operator is able to switch the laser on.
3. DMX input: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller.
4. DMX output: 3pin female XLR-connector used to connect the laser with the next unit in the DMX chain.
5. DISPLAY: shows the selected DMX address when the unit is in DMX-mode. Apart from DMX-mode you
can also select 5 other modes, see further for these different operation modes.
JB SYSTEMS
®
OPERATION MANUAL
3/48 LOUNGE LASER DMX
ENGLISH
6. CONTROL PANEL: Used to control the different functions of the laser, see further to learn how to
operate the unit.
7. HANGING BRACKET: with 2 knobs on the sides to fasten the unit and a mounting hole to fix a
mounting hook.
8. SAFETY EYE: used to attach a safety cable when the unit is rigged (see paragraph "overhead rigging")
9. LASER APERTURE: Here the laser beam leaves the enclosure; make sure to NEVER look inside the
unit through this opening while the laser effect is switched on!
10. LED LENS: Here the LED-effect leaves the enclosure.
11. WARNING LABEL: "Laser Radiation. Avoid exposure to beam. Class 3B laser product"
12. LASER WARNING SIGN: warns against a potentially dangerous laser when not used by skilled
operators.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
CAUTION EYEDAMAGE: Always position the laser in a way that prevents the audience
from looking directly into the laser beams. The installation should assure that the beam
will not strike the audience.
JB SYSTEMS
®
OPERATION MANUAL
4/48 LOUNGE LASER DMX