Lamp Replacement; Overhead Rigging - BEGLEC JBSYSTEMS Lihgt MINI LOGO Mode D'emploi

ENGLISH
DESCRIPTION:
1. Optical lens with manual focus adjustment
2. Hanging bracket with 1 knob to fasten the unit and a mounting hole (M8) to fix a mounting hook like
CR16/30.
3. Mains power cable
4. Fuse holder
5. Lamp compartment.
6. Internal microphone (not used)
7. Cooling fan
8. switch for rotating gobo.
LAMP (RE)PLACEMENT
In case of replacement of the lamp or maintenance, do not open the fixture within 10
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When
replacing parts, please only genuine spare parts.
• Switch off the unit and unplug the mains cable.
• Wait for about 10 minutes until the unit has been cooled down.
• Unscrew the screw that closes the lamp compartment of the fixture.
• On the inside you will see the lamp socket. Tear the lamp socket gently
out of the lamp compartment.
• Unplug the old lamp. Hold the lamp socket while unplugging the lamp
instead of pulling the cable!
• Hold the lamp socket while pressing the new lamp gently in the socket.
Attention! Check the label on the backside of the device or see the
technical specifications in this manual to know which lamp should be used.
Never install lamps with a higher wattage! Lamps with higher wattage
generate temperatures the device was not designed for. If the device uses
a lamp transformer, it will burn due to current overload.
• Don't touch the bulb inside the reflector of the lamp with bare hands! This
drastically shortens the lifespan of the lamp. If you touched the lamp, clean
it with a cloth and a little denatured alcohol. Wipe the lamp off before
installing.
• Put the new lamp back inside the unit. Be sure that the wires don't touch
the lamp.
• Close the lamp compartment with the screw.
• Done!
JB SYSTEMS®
OPERATION MANUAL
3/18 MINI LOGO
ENGLISH
EXCHANGING A GOBO
The logo projector accepts metal gobos: D= 26,8mm (image D= 20mm)
• Switch off the main supply and unplug the unit.
• Wait for about 10 minutes until the unit has been cooled down.
Loosen the screw that Remove the cover of the
closes the lamp lamp compartment
compartment of the fixture gently loosen the screw that
fixes the gobo holder
Put the new gobo in place. Put the fixation ring gently
Make sure you can read the back in place using a small
text on the gobo when you pincer.
look from the reverse side
otherwise your text will be
mirrored.
• Put the cover of the lamp compartment back in place and tighten the screw.
• Done!

OVERHEAD RIGGING

• Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
• Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
JB SYSTEMS®
OPERATION MANUAL
Remove the gobo holder Remove the fixation ring
and
of the gobo. You can do
this easily with a small
pincer. Take the gobo
gently out of the holder.
Make sure that the end Put the gobo holder back in
place and tighten the screw
of the fixation ring locks
firmly to keep the gobo
in the groove of the gobo
holder in place. Important:
holder.
make sure the gear wheel
is well fixed!
4/18 MINI LOGO