Using The Showview Feature; Showview Extended - Samsung DVD-VR350 Manuel D'instructions

DVD-Recorder
Programme
DVD-RAM(VR)
Title List
ShowView
Playlist Scheduled Record List

ShowView Extended

: Off
Disc Manager
Programme
Setup
Copy
MOVE OK RETURN EXIT
DVD-Recorder ShowView
DVD-RAM(VR)
Title List
Playlist
Enter ShowView Code number. [0-9]
Disc Manager
Programme
Setup
Copy
NUMBER OK RETURN EXIT
DVD-Recorder Scheduled Record List
DVD-RAM(VR) Current Time 12:00
No. To Source Day Start End Speed V/P Edit
No. 01
To Source Day Start End Speed V/P
DVD PR 01 01 MON 12:00 14:00 SP Off
Available Time 00:48 SP
MOVE OK RETURN EXIT
DVD-Recorder
Scheduled Record List
DVD-RAM(VR) Current Time 12:00
No. To Source Day Start End Speed V/P Edit
01 DVD PR 01 Daily 12:00 14:00 SP Off
02 - - - - - - - - - - - - -:- - - -:- - - - - -
MOVE OK RETURN EXIT
DVD-Recorder
Programme
DVD-RAM(VR)
Title List
ShowView
Scheduled Record List
Playlist
ShowView Extended : Off
Disc Manager
Programme
Setup
Copy
MOVE OK RETURN EXIT
DVD-Recorder Programme
DVD-RAM(VR)
Title List
ShowView
Scheduled Record List
Playlist
Off
ShowView Extended : Off
10
Disc Manager
20
Programme 30
40
Setup
50
60
Copy
MOVE OK RETURN EXIT

Using the ShowView Feature

►
►
Before presetting your DVD Recorder & VCR:
►
• Switch on both the television and your DVD Recorder & VCR.
• Check that the date and time are correct.
Up to twelve programmes can be preset.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Programme, then press the OK or ► button.
3. Press the ▲▼ buttons to select ShowView, then press the OK or ► button.
• A message is displayed to allow you to enter the ShowView code.
4. Press the number buttons to enter the code of the programme that you
want to record in your television magazine.
• If you want to correct the ShowView code that you are entering:
• Press the ◄ button until the digit to be corrected is cleared.
• Enter the correct digit.
5. Press the OK button.
• The information concerning the programme is displayed.
• When using the ShowView function for the fi rst time with stored
stations, the programme number fl ashes. This one time, you must
enter the PR number manually by pressing the ▲▼ buttons.
6. If the programme and times are correct, press the OK button.
7. Turn the power off by pressing the STANDBY/ON button to activate
the timer recoding setting.
8. Refer to pages 56~57 if you want to:
• Check whether the timer Recording has set correctly or not.
• Cancel a preset recording.
■ The numbers next to each TV programme listing in the
►
magazines or newspapers are ShowView code numbers, which
►
allow you to programme your DVD Recorder & VCR instantly
with the remote control.
■ ShowView is a trademark of Gemstar Development Corporation.
The ShowView system is manufactured under licence from
Gemstar Development Corporation.
ShowView Extended
To prevent delays or over-runs the DVD Recorder & VCR has a
►
function called ShowView Extended allowing you to extended the
►
recording time by up to 60 minutes.
►
• Only use if PDC is not available or set to OFF.
1. With the unit in Stop mode, press the MENU button.
2. Press the ▲▼ buttons to select Programme, then press the OK or ► button.
3. Press the ▲▼ buttons to select ShowView Extended, then press the
OK or ► button.
►
4. Press the ▲▼ buttons to select the ShowView Extended time, then
►
the press OK or ► button.
►
5. Press the EXIT button to exit the menu.
English - 59
DVD-VR355 only