Progressive Scan - Samsung DVD-VR350 Manuel D'instructions

▌

Progressive Scan

Your TV must support progressive scan input to
allow to watch progressive scan component video
out. (See page 29)
• For more information about Progressive setting, refer to
the page 29.
• Make sure that the colour coded connections match.
That is, the Y, P and P component output jacks of
B R
your DVD Recorder & VCR should be connected to the
exact corresponding component input jacks on your TV.
Otherwise, red or blue images will be displayed on the
TV screen.
• Consumers should note that not all high defi nition
television sets are fully compatible with this product
and may cause artifacts to be displayed in the picture.
In case of progressive scan picture problems, it is
recommended that you switch the connection to the
standard defi nition output.
If there are questions regarding your Samsung TV set'
s compatibility with this DVD Recorder & VCR, please
contact our customer service centre.
■ See your TV User's Manual to fi nd out if your TV
supports Progressive Scan.
If Progressive Scan is supported, follow the TV
User's instructions regarding Progressive Scan
settings in the TV's menu system.
■ Depending on your TV, the method of connection
may differ from the illustration above.
■ What is "Progressive Scan"?
Progressive scan has twice as many scanning
lines as the interlace output method has.
Progressive scanning method can provide better
and clearer picture quality.
■ You must connect the DVD Recorder & VCR to
the component(s) before using the Progressive
Scan feature.
■ The Component jacks will not output video
resolutions above 576p.
To view 720p and 1080i, connect the DVD
Recorder & VCR to your TV with the HDMI cable.
With HDMI connected, press the P.SCAN button
to alternate between all available resolutions.
(See page 29) (DVD-VR355 only)
Connecting HDMI/DVI to a TV
(DVD-VR355 only)
If your TV has a HDMI/DVI input, connect the HDMI/
DVI cable to the TV. You will enjoy the best quality
images and sounds.
▌ Case 1 : Connecting to a TV with HDMI Jack
• Using the HDMI cable, connect the HDMI OUT jack on
the rear of the DVD Recorder & VCR to the HDMI IN
jack of your TV.
• Press the input selector on your TV remote control
until the HDMI signal from the DVD Recorder & VCR
appears on your TV screen.
▌ Case 2 : Connecting to a TV with DVI Jack
• Using the DVI Adapter Cable, connect the HDMI OUT
jack on the rear of the DVD Recorder & VCR to the DVI
IN jack of your TV.
• Using the audio cables, connect the AUDIO (red and
white) OUT jacks on the rear of the DVD Recorder &
VCR to the AUDIO (red and white) IN jacks of your TV.
Turn on the DVD Recorder & VCR and TV.
• Press the input selector on your TV remote control until
the DVI signal from the DVD Recorder & VCR appears
on your TV screen.
■ To watch through the HDMI output, set the
digital audio output to PCM. (See page 27)
■ Depending on the HDMI device (TV/HDMI Receiver)
you use, audio may not be supported. If TV does
not support Dolby digital/DTS, Audio output is not
available when you set Digital output as Bitstream
or select DTS On in Audio setup menu. In this case,
set the digital audio output to PCM or DTS off.
■ If you connect the HDMI cable between Samsung
TV, you can operate easily DVD Recorder
& VCR using the TV remote control. (This is
only available with Samsung TVs that support
Anynet+(HDMI-CEC).) (See pages 34~35)
■ Please check the
logo, then it supports Anynet+ function.)
English - 19
HDMI cable
(not supplied)
logo (If your TV has an