8rpvÃÃr
ÃyÃvp
rÃ7Ã
1. Insert the coupling member of the power
cable to the plug of the spring-loaded safety
push button.
2. Form a loop from the power cable and slide it
into the cable relief. The loop of the power
cable must be long enough to be able to
slide from one side to the other.
TvpuvtÃurÃ
ÃÃvp
rÃ8ÃhqÃ9Ã
1. Press the safety push button and keep
pressed.
2. Pull the safety handle against the bar. The
motor starts.
Ir)
Uur hsr uhqyr qr rthtr D
ir uyq hyy ur vr
3. Let go the safety push button.
TvpuvtÃurÃ
ÃssÃ
1. Let go of the safety handle. The safety han-
dle automatically returns to the zero position.
The motor is now turned off.
htr
Ä
!
6sr
ur
uh irr vpurq ss
ur
yyr
pvr
hr s
h sr
rpq
±
ur
rs
r
uhq qr
ur hyvhpr
hvtu hh
2SHUDWLQJ LQIRUPDWLRQ
Ir)
7rs
r vt ur hyvhpr purpx v s
rr
hy qhhtr Uur t
rr h
xvt s
ur vphy hsr qvyh ir vviyr
$
−
To start the appliance, the roller must be
completely unobstructed.
−
Don't bring your hands and feet close to
rotating parts.
−
Operate the appliance only, when the safety
distance defined by the guiding bar is com-
plied with.
−
Keep the power cable safely.
−
Drive the appliance only at walking speed.
−
Make sure you have a good standing while
using the appliance.
−
Do not scarify along steep slopes.
−
Always scarify at right angle to slopes, never
directly upwards or downwards.
−
Caution while changing direction during work
on slopes.
q
−
Caution while making turns with the appli-
ance or approaching it to persons.
−
Never tilt or transport appliance with running
motor.
−
Never leave the appliance unattended.
−
When leaving, disconnect the appliance from
the power supply.
8urpxvtÃiÃhÃrr
ÃvÃrprh
Ã
−
after hitting an obstacle
−
if the motor comes to an immediate standstill
−
if the blades of the scarifier roller are bent
−
if the toothed belt is defective
−
if the wire leading to the motor is damaged
−
if there are other damages.
0DLQWHQDQFH DQG FDUH
9htr
Ä
!
Qyy ur yt irs
r h hvrhpr
hq
hv
s
Srhv
s ur hyvhpr h y ir
rrprq i h hu
vrq qrhyr
0DLQWHQDQFH UDWHV
7rs
rÃrhpuÃr
hvÃ
1. Make a visual control of the appliance.
2. The appliance must not be used, when nuts,
bolts, screws or other parts are missing, de-
fective or loose.
3. Make a visual control of the connection line.
Don't use faulty connection lines (e. g. with
cracks, cutting, crushing or bucking signs in
the insulation).
4. Check rear flap and/or grass box for wear
and damages.
8yrhvtÃurÃhyvhprÃ
Clean the appliance after each use.
6rvÄ
Irr
yhu
hr
ph
qr
hsr yt
Clean the roller with a spatula, brush etc.
htr
Ä
!
Svx s vw
ur iyhqr s ur
yyr
Xrh
rpvr tyr
h
hqvyy
s
ur
yyr
vu
hr
Qrr
hvt
ur
hq
GB 3
ur