Breville Dual Boiler BES900XL /B Fonctionnement page 16

CARE & CLEAnInG
CLEAnInG thE StEAM WAnD
• Immediately after texturing milk, wipe
the steam wand with a damp cloth and
purge (by lifting the STEAM LEVER for
a few seconds).
• If any of the holes in the tip of the
steam wand become blocked, ensure
the STEAM LEVER is in the CLOSED
position and clean using the pin on the
end of the provided cleaning tool.
• If steam wand remains blocked, remove
the tip using the integrated spanner in
the cleaning tool and soak in hot water.
Screw tip back onto the steam wand
using the integrated spanner in the
cleaning tool.
CLEAnInG thE fILtER BASkEtS
AnD PoRtAfILtER
• The filter baskets and portafilter should
be rinsed under hot water directly after
use to remove all residual coffee oils.
• If the holes in the filter baskets become
blocked, dissolve a cleaning tablet in
hot water and soak filter basket and
portafilter in solution for approx. 20
minutes. Rinse thoroughly.
CLEAnInG thE ShoWER SCREEn
• The group head interior and shower
screen should be wiped with a damp cloth
to remove any ground coffee particles.
• Periodically purge the machine with
hot water (see 'Advanced Functions',
page 19) with the filter basket and
portafilter in place, without ground
coffee, to rinse out any residual coffee.
30
CLEAnInG thE DRIP
& StoRAGE tRAy
• The drip tray should be removed,
emptied and cleaned after each use or
when the drip tray indicator is showing
Empty Me!
• Remove grill from the drip tray. Wash
both in warm soapy water. The Empty
Me! indicator can also be removed from
the drip tray.
• The storage tray can be removed and
cleaned with a soft, damp cloth (do not
use abrasive cleansers, pads or cloths
which can scratch the surface).
CLEAnInG thE oUtER hoUSInG
& CUP WARMInG tRAy
• The outer housing and cup warming tray
can be cleaned with a soft, damp cloth.
Polish with a soft, dry cloth. Do not use
abrasive cleansers, pads or cloths which
can scratch the surface.
notE
Do not clean any of the parts or
accessories in the dishwasher.
CARE & CLEAnInG
USInG thE ALLEn kEy
Over time, the silicone seal surrounding the
shower screen will need to be replaced to
ensure optimum brewing performance.
Press the Power button to turn the
1.
machine Off and unplug the cord from
the power outlet.
Carefully remove the rear water tank
2.
and drip tray, taking particular care if
they are full.
Using a skewer or similar, clean
3.
the center of the screw of any residual
coffee.
Insert the shorter end of the Allen
4.
Key into the center of the screw. Turn
counter-clockwise to loosen the screw.
Clean center of screw
before inserting Allen key
Once loosened, carefully remove and
5.
retain the screw, stainless steel shower
screen and black dispersion plate. Make
note of the side of the shower screen
and dispersion plate that are facing
downwards. This will make re-assembly
easier. Wash the shower screen and
dispersion plate in warm soapy water,
then dry thoroughly.
Remove the silicone seal with your
6.
fingers or a pair of long-nose pliers.
Insert the new seal, flat side first, so the
ribbed side is facing you.
Re-insert the dispersion plate, then the
7.
shower screen, then the screw. With
your fingers, turn the screw clockwise
for 2-3 revolutions then insert the Allen
Key to tighten until the screw is flush
with the shower screen.
Re-insert the drip tray and rear water
8.
tank.
Contact Breville Consumer Service or visit
www.breville.com for replacement silicone
seals or for advice.
31