Alutech LG-600F-868 Manuel D'installation Et D'utilisation page 23

ADjUSTMENT
No—'position control' is off;
on—'position control' is on.
Default value—'no. '
4.6
Press ; after that a dot
will appear on the display
To exit the menu, press
4.7
or wait for 15 seconds
P2—RADIO CONTROL SETUP
P2–F1—Recording the radio controls in the
5 one-button control mode with function
'step-by-step' (SBS) into the memory
Press and hold
5.1
for about 5 secs to enter the
programming mode
Using and
5.2
select program 'P2' on the
menu
5.3 Press
Using and
5.4
select function 'F1' on the
menu
5.5 Press
'rc' is shown on the display,
which means that the
5.6 recording of remote controls
in 'step-by-step' mode is
expected
Press the selected control
5.7 button on the remote control
three times
The indicator will
automatically show the
number offered for a remote
control in the drive memory
5.8
(the number can be changed
using buttons
Press to confirm; after
5.9
that a dot will appear on the
display
LEVIGATO DRIVES (LG SERIES)
and
| LEVIGATO ANTRIEBE (SERIE LG)
In one second the automatic
switch to the recording of
the next remote control will
take place.
5.1
To exit the programming
mode press
for 15 seconds
P2-F2—Recording the radio controls in the
two-buttons control mode with functions
6
'step-by-step' (SBS) and 'pedestrian position
(PE)' into the memory
The setup is similar to that in item 5 of Table 6,
but for program 'P2' and function 'F2' .
ATTENTION!
6.1
The button, pressed during the programming,
will send commands 'step-by-step' , and the next
button—command to move to the 'pedestrian
position (PE)'
P2-F3—Recording the radio controls in the two-
7
buttons control mode with functions 'step-by-
step' (SBS) and 'light lamp (LL)' into the memory
The setup is similar to that in item 5 of Table 6,
but for program 'P2' and function 'F3' .
ATTENTION!
7.1
The button, pressed during the programming,
will send commands 'step-by-step' , and the next
button—'light lamp (LL)' control commands
P2-F4—Recording the radio controls in the
three-buttons control mode with functions
8
'step-by-step' (SBS), 'pedestrian position (PE)'
and 'light lamp (LL)' into the memory
The setup is similar to that in item 5 of Table 6,
but for program 'P2' and function 'F4' .
ATTENTION!
The button, pressed during the programming,
8.1
will send commands 'step-by-step' , and the next
buttons—command to move to the 'pedestrian
position (PE)' and 'light lamp (LL)' control
command
P2-F5—Recording the radio controls in the
three-buttons control mode with functions
9
OPEN (OP), STOP (STOP), CLOSE (CL) and
'pedestrian position (PE)' into the memory
The setup is similar to that in item 5 of Table 6,
but for program 'P2' and function 'F5' .
ATTENTION!
The button, pressed during the programming,
9.1
will send command OPEN (OP), and the next
buttons—command STOP (STOP), CLOSE (CL)
and command to move to the 'pedestrian
position (PE)'
P2-F6—Recording the radio controls in the
three-buttons control mode with functions
10
OPEN (OP), STOP (STOP), CLOSE (CL) and 'light
lamp (LL)' into the memory
| COMMANDES LEVIGATO (SERIE LG)
or wait
21