SSS Siedle BFCV 850-02 Information Produit page 7

English
Application
Comfort handsfree bus telephone
intercom with colour monitor 8.8 cm
for the Siedle In-Home bus, made of
high-grade plastic.
With the functions calling, speech,
vision, door release, light, storey call/
switching and control functions and
internal communication.
Performance features:
• Integrated video memory for 28
colour pictures (file format *.tif,
720 x 576 Pixel). Additional power
supply required
• Upgradable with SD card (32 MB
to 32 GB utilizable space)
• Monitor button for image con-
nection
• Integrated 5-way control button
for operation of the video memory,
zoom, brightness, colour saturation,
setting the date and time, ...
• Integrated audio and video privacy
device.
• Status display with active speech
connection
• Call silencing with status display.
• Parallel operation of
max. 8 BFCV 850-... units (additional
installation/supply required).
• Programming possible via
PRI 602-... USB and ZBVG 650-...
• Call differentiation for storey call, 2
door calls and internal call
• Call differentiation for internal calls
• Set call-back
• 11 different electronic call tones to
chose from
• Call volume adjustable in 5 stages
up to max. 83 dB(A).
• 8 LEDs for display (e.g. door open)
without additional wiring
• 8 integrated function keys, 7
freely programmable and capable
of double assignment. Optionally
assignable button functions can
be triggered without supplemen-
tary installation via bus cores, e.g.
for internal telephony, to initiate
switching/control functions in con-
junction with bus switching module
BSM/BSE 650-..., selective dialling of
door loudspeakers/cameras
• Integrated inscription panel
• Door call acceptance
• Group formation for door calls.
Each BFC(V) 850-... can belong to up
to 4 groups in the same line.
• Large-area buttons (as speech/
control buttons)
• Door release/light function at any
time by means of bus wires
• Door/video connection at any time,
also possible without prior door call
• Base plate pre-installable with
terminals
• Can be used as a table-top unit
using table-top accessory
ZTCV 850-...
Intercom functions:
• Call forwarding
• Internal group call
• Collective announcement (addi-
tional supply required)
• Automatic call pick-up of internal
calls
• Doormatic
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply
• BFCV 850-... (Base plate and
housing with circuit board)
• Dummy card for SD card slot
• Operating instructions for the
end user
• This product information
Mounting
Strip back cable to appr. 80 mm.
1 Recommended mounting height
appr. 1.50 m to centre device.
2 Open the device from the back;
by releasing the base plate with the
locking lever.
3 When mounting directly on the
wall, fasten the base plate using
4 screws, paying attention that
the plate is the right way up (top
marking). When mounting on a
switch box, use the screw openings
in the centre of the device, paying
attention that the plate is the right
way up (top marking).
4 Install in accordance with the
wiring diagram. The cores of the
installation cable must be stored
inside the free installation space in
the base plate.
5 Hook the housing into the
base plate from above and close
by exerting a slight pressure.
Depending on the installation envi-
ronment, it may be necessary to
change the microphone sensitivity
of the BFCV 850-... in order to
permit clear speech transmission.
If a speech connection exists, press
the door release button and light
button simultaneously. Using the
speech button +/- the microphone
sensitivity can be set. If no input is
made within 10 seconds, the micro-
phone setting switches off again.
Save the set microphone sensitivity
by pressing the muting button for
3 seconds.
Dismantling
6 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board
remains in the housing superstruc-
ture.
Lettering
7 The lettering panel can be
inscribed to indicate the button
functions. The see-through panel
can be lifted at the side.
5