Publicité
Les langues disponibles
Les langues disponibles
Getting Started: Initial Operation
Unpacking the Model
Remove the styrofoam packaging
extremely carefully to prevent damaging
accessories and attached parts such as
handrails etc.
Initial Operation
We recommend letting the locomotive run
without a train for 30 minutes in both
directions, to properly break it in. This will
help achieve optimal performance and
longevity for the locomotive. Of course,
your model should only be run on smooth
and perfectly clean tracks with reliable
electrical contact to all track sections.
Technical Data
Power Supply
The model should only be operated on a
pure, filtered DC power supply of 0 to 24
volts, with a capacity of at least 1 Amp
and a fast-acting fuse or circuit breaker to
protect against short circuits. Do not use a
power supply which is not in safe and
perfect working condition. (See "Digital
Decoder" section for operation on digital
power.)
Mechanism
The locomotive has a powerful high-
precision motor, which turns the wheels
through a robust gearbox.
Lighting
The model is equipped with automatic
directional headlights, using white LEDs for
a realistic appearance. The "front" lights
are illuminated according to the travel
direction.
Radius
The locomotive can run on a track with a
minimum recommended radius of 600 mm
(23.62'').
Digital Decoder
The model locomotive is prepared for
"plug and play" installation of a PIKO
# 36122 Multi-Protocol Decoder (available
separately). As soon as the decoder is
properly installed, the locomotive can be
operated on digital as well as Analog DC-
powered layouts.
Sound Module
Only the model of the V 60 is prepared for
"plug and play" installation of a PIKO # 36195
Sound Unit (available separately). This
reproduces authentic sounds of the real V 60.
It requires that the loco be equipped with a
PIKO # 36122 multi-protocol decoder. The
sound unit must be connected to the multi-
protocol decoder via the included interface
cable. The sound unit includes a high-quality
extended frequency range speaker with a
waterproof diaphragm for outdoor operation.
Note: The sound unit is operable only on
digital layouts, not on analog DC-powered
layouts.
Maintenance
Lubrication
After each 25 hours of operation, and after
any long periods of storage, please lubricate
the locomotive's gears with a sparing amount
of plastic-compatible, non-hardening grease.
Remove the gearbox bottom cover and be
careful to keep the front and rear wheelsets
aligned with each other. Be sure to securely re-
tighten the gearbox bottom cover screws.
Cleaning
If cleaning is necessary, use only a mild
cleaning agent (such as soap and water) and
gentle action with a soft non-abrasive cloth or
brush. Never immerse the loco in liquid or
"flood" any internal parts!
Wheel Wipers and pick-Up shoes should be
changed after 500 hours of operation.
Please Note!
Damage to Carpets and Other Surfaces:
Normal operation of the locomotive
causes wear of mechanical parts (wheels,
electrical pickups etc.). This produces
carbonized dust, grease and oil, which can
permanently stain carpets, wood floors
and other materials. It is the user's
responsibility to take proper precautions
against this damage. Wipe any grease or
oil from the track rails with a clean soft
cloth. PIKO Spielwaren GmbH, as well as
its representatives, distributors and
retailers, assume no liability for any such
damage.
Please Note!
Important Safety Precautions
• Check the power supply regularly for any
damage or problems.
• Do not use a malfunctioning or damaged
power supply!
• This model must only be operated with
one power source per circuit!
• This product is not a toy, not suitable for
personnel under 8 years of age. This
product has small parts, sharp parts, and
moving parts.
• This model must only be operated with a
safety-assured power supply with the
identification!
• The power supply is not a toy!
• Disconnect the model from the power
supply before cleaning or servicing!
• Do not insert the track power connecting
wires into household "mains" voltage
outlets.
5
Publicité
