Initial Operation - PIKO V20 Manuel D'utilisation

37550-90-7000.qxd 19.06.2015
Getting Started: Initial Operation
Unpacking the Model
Remove the styrofoam packaging
extremely carefully to prevent
damaging accessories and attached
parts such as handrails etc.

Initial Operation

We recommend letting the locomotive
run without a train for 30 minutes in
both directions, to properly break it
in. This will help achieve optimal
performance and longevity for the
locomotive. Of course, your model
should only be run on smooth and
perfectly clean tracks with reliable
electrical contact to all track sections.
Technical Data
Power Supply
The model should only be operated
on a pure, filtered DC power supply of
0 to 24 volts, with a capacity of at
least 2 Amp and a fast-acting fuse or
circuit breaker to protect against short
circuits. Do not use a power supply
which is not in safe and perfect
working condition. (See "Digital
Decoder" section for operation on
digital power.)
Mechanism
The locomotive has a powerful high-
precision motor, which turns the
wheels through a robust gearbox.
11:29 Uhr Seite 5
Lighting
The model is equipped with automatic
directional headlights, using white
LEDs for a realistic appearance. The
"front" lights are illuminated
according to the travel direction.
Digital Decoder
The model locomotive is prepared for
"plug and play" installation of a PIKO
#36122 Decoder (available separately).
As soon as the decoder is properly
installed, the locomotive can be
operated on digital as well as Analog
DC-powered layouts.
Sound Module
Only the model is prepared for "plug and
play" installation of a PIKO #36224
Sound Unit (available separately). This
reproduces authentic sounds of the real
V20. It requires that the loco be equipped
with a PIKO # 36122 decoder. The sound
unit must be connected to the decoder
via the included interface cable. The
sound unit includes a high-quality
extended frequency range speaker with a
waterproof diaphragm for outdoor
operation. Note: The sound unit is
operable only on digital layouts, not
on analog DC-powered layouts.
Maintenance
Lubrication
After each 25 hours of operation, and
after any long periods of storage, please
lubricate the locomotive's gears with a
sparing amount of plastic-compatible,
non-hardening grease. Remove the
gearbox bottom cover and be careful to
keep the front and rear wheelsets aligned
with each other. Be sure to securely re-
tighten the gearbox bottom cover screws.
Cleaning
If cleaning is necessary, use only a mild
cleaning agent (such as soap and water)
and gentle action with a soft non-
abrasive cloth or brush. Never immerse
the loco in liquid or "flood" any internal
parts!
Wheel Wipers and pick-Up shoes should
be changed after 500 hours of operation.
Please Note! Damage to Carpets and
Other Surfaces: Normal operation of
the locomotive causes wear of
mechanical parts (wheels, electrical
pickups etc.). This produces
carbonized dust, grease and oil,
which can permanently stain carpets,
wood floors and other materials. It is
the user's responsibility to take
proper precautions against this
damage. Wipe any grease or oil from
the track rails with a clean soft cloth.
PIKO Spielwaren GmbH, as well as its
representatives, distributors and
retailers, assume no liability for any
such damage.
Please Note!
Important Safety Precautions
• Check the power supply regularly for any
damage or problems.
• Do not use a malfunctioning or damaged
power supply!
• This model must only be operated with
one power source per circuit!
• This product is not a toy, not suitable for
personnel under 14 years of age. This
product has small parts, sharp parts, and
moving parts.
• This model must only be operated with a
safety-assured power supply with the
identification!
• The power supply is not a toy!
• Disconnect the model from the power
supply before cleaning or servicing!
• Do not insert the track power connecting
wires into household "mains" voltage
outlets.
5