Remote Control Battery Change; Manoeuvring The Caravan; Coupling To A Towing Vehicle; Maintenance - Truma Mover XT Mode D'emploi / Instructions De Montage

LED 3 red lights up in the event of a persistent fault, and an
acoustic signal is also emitted
e.g. in the event of a faulty drive motor
Apply the handbrake. See "Troubleshooting"
LED 4 green flashes if radio connection has not yet been es-
tablished after switching on the remote control
lights up when remote control is ready for opera-
tion and the data link is stable
flashes in combination with acoustic signal
– 10 seconds after switching on the remote control if the
control unit is not yet ready for operation
– if the control unit has been switched off
– after 1 minute without pressing a button on the remote
control
– after a radio communication interruption
All LEDs "off" and no audio signal
System off
(check batteries in remote control if necessary)

Remote control battery change

Only use micro-batteries that will not leak,
type LR 03, AAA, AM4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.
Fig. 3
Empty, used batteries can leak and damage the remote
control! Remove the batteries if the remote control is
not being used for a long period of time.
No warranty given for damage caused by leaking
batteries.
Before disposing of a defective remote control, always re-
move the batteries and dispose of them correctly.

Manoeuvring the caravan

Follow the "Safety instructions" before using the
Mover® XT / XT2.
Apply parking brake if caravan is uncoupled.
Disconnect 13-pin plug from vehicle and plug into safety
socket of caravan.
For safety reasons, the Mover® XT / XT2 can only be op-
erated if the 13-pin plug of the caravan is plugged into
the safety socket.
In the event of a malfunction, the 13-pin plug may only
be removed from the safety socket if the handbrake has
been applied, since the electronic safety functions are disabled.
Switch on the remote control – green LED 4 flashes until the
control unit is ready for operation. If the control unit is not
ready for operation, the remote control switches off after
about 10 seconds.
18
Press the two buttons (i) for engaging simultaneously, and en-
gaging will start after approx. 3 seconds (safety delay).
Use the position indicator to check that both drive rollers
are correctly engaged.
Before starting the Mover® XT / XT2,
release the parking brake.
Movement in all directions is possible using the control knob
and the slide control.
The Softstart/Softstop makes the caravan start to move
without jolting, and brakes it gently when stopping.
When the control knob or slide control are released, or if the
radio signal is interrupted or becomes too weak, the caravan
stops moving. Radio equipment and other Mover® remote
controls will not activate your Mover®.
After start-up, the Mover® XT / XT2 moves at a steady speed
(according to the setting on the slide control). Speed increas-
es slightly on downhill slopes and decreases on uphill slopes.
After manoeuvring, apply the parking brake first and then
disengage the drive rollers from the tyres.
Move slide switch on remote control to the "Off" position
to switch the remote control off (the Mover® XT / XT2 switch-
es to standby mode).
The slide switch also acts as an "Emergency Stop"
switch.
Remove the plug from the safety socket after manoeuvring,
otherwise the control unit will automatically switch off after
1 hour. The battery is discharged with a quiescent current of
approx. 80mA if the plug is in the socket.

Coupling to a towing vehicle

The Mover® XT / XT2 allows a caravan to be coupled to a
towing vehicle without jolting and with millimetric precision.
However, this requires care and a degree of practice.
Following the operating instructions, move the caravan close
to the towing vehicle (apply parking brake and engage gear).
In order to position the caravan precisely, operate the control
knob or slide switch until the caravan's coupling is located
precisely over the ball coupling on the towing vehicle. Then
couple the caravan to the vehicle by lowering it at the support
wheel in the usual manner.
Prepare the caravan for towing in the usual way.
The caravan must not be towed with the drive rollers
engaged.

Maintenance

Keep drive elements clear of coarse road dirt. When cleaning
the caravan, spray the Mover® XT / XT2 with a water hose to
remove mud etc. Make sure that no stones, twigs etc. are
trapped in it. The control unit does not require servicing. The
remote control must be kept in a dry place.
Clean the Mover® XT / XT2 as described above every year (or
before overwintering). Do not park the caravan with the drive
rollers engaged.
To prevent the battery from becoming totally discharged dur-
ing long periods of inactivity it must be disconnected and
recharged before using again. Charge the caravan battery
before starting up.
It is extremely easy for you or your caravan dealer to perform
the checking and maintenance of your Mover® XT / XT2 dur-
ing the annual inspection of your caravan. In case of doubt,
please contact Truma Service or one of our authorised service
partners (see Truma Service Booklet or www.truma.com).