PrimAster KZS1500 Traduction Des Instructions D'origine page 29

8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)
The crosscut saw can be used to make crosscuts
of 0° -45° to the left and 0° -45° to the right in rela-
tion to the stop rail.
Important. To make 90° crosscuts, the adjustable
stop rail (16a) must be fixed at the inner position.
• Open the set screw (16b) for the adjustable stop rail
and push the adjustable stop rail inwards.
• The adjustable stop rail (29) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen set screw (26).
• Use the handle (11) to adjust the rotary table (14)
to the desired angle. The pointer (12) on the rotary
table must match the desired angle on the scale
(13) on the fixed saw table (15).
• Re-tighten the set screw (26) in order to secure the
rotary table (14).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre
cut 45° (Fig. 1/10/11)
• No stop angle included.
• Lower the machine head (4) and secure using the
locking bolt (23).
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to
angle the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
• Adjust the adjusting screw (28) until the angle be-
tween the saw blade (6) and rotary table (14) is pre-
cisely 45°.
• It is not necessary to fix this setting because it is
maintained by the spring pretension.
• Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 45° on the angle
scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0°
(Fig. 1/2/12)
The crosscut saw can be used to make mitre cuts
of 0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (16a) must be fixed
at the outer position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (19) indicates the desired angle measure-
ment on the scale (18).
• Re-tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/4/13)
The crosscut saw can be used to make mitre cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° to the left or 0° -
45° to the right in relation to the stop rail (double
mitre cut).
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (16a) must be fixed
at the outer position.
• Open the set screw (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
• The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set
screw (26).
• Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
• Re-tighten the set screw (26) in order to secure the
rotary table.
• Undo the locking screw (22) and use the handle (1)
to tilt the machine head (4) to the left until it coin-
cides with the required angle value (in this connec-
tion see also section 8.6).
• Re-tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
• The cutting depth can be infinitely adjusted using
the screw (24). To do this loosen the knurled nut on
the screw (24). Move the stop for the cutting depth
limitre (25) to the outside. Turn the screw (24) in or
out to set the required cutting depth. Then re-tight-
en the knurled nut on the screw (24).
• Check the setting by completing a test cut.
GB | 29