Güde GKM 5,5 B&S 3 IN 1 Mode D'emploi page 18

The speed control lever must in dangerous situations and
accidents be put to "TOP" and engine switched off by the
engine switch (pic. 9; pos. "OFF").
In the operating mode, make always sure that the cooling
and combustion air is exhausted without interruption
(leaves may block the exhaust channels). Flue gas exhaust
without interruption should be ensured, too.
Supporting wheel and brush height adjustment
As soon as the brushes are slightly worn out, distance of
brushes from the ground must be adjusted again. For that
purpose, plastic rings of the brush supporting wheel must be
calibrated again.
Remove the lock rings of the supporting wheels and the
required number of plastic rings (see pic. 3a) from the
bottom side. Fit the supporting wheels again (pic. 3b). The
supporting wheel goes up and brushes are nearer to the
ground. Fit the plastic rings to the upper side and fix them
using a spacing bushing and locking ring so that the hole
distance towards the bushing remains constant (pic. 3c)
Finishing your work or breaks
After final sweeping is completed, let the appliance run free with
no load for 1 to 2 minutes (engine cooling phase)
Inspections and maintenance
Have any repairs necessarily performed by trained professional
staff only.
The socket plug must be pulled out before any appliance
changeover, adjustment or maintenance.
Safety instructions for inspections and maintenance
- Make sure petrol or oil do not leak – wear protective gloves
when working near the sweeping brush!
The sweeper, especially the sweeping brush, must be
cleaned after each use.
Maintenance, treatment, repairs, storing
General instructions
Safety instructions in particular should be followed.
Follow the engine servicing instructions included in the
B&S manual.
Regular maintenance is necessary for perfect working of
your sweeper.
Sweeping brushes and driving components in particular must
be carefully treated to prevent damages or accidents in general.
Before maintenance:
- pull down the socket plug,
put the appliance to a stable position,
-
wait until the engine cools down.
-
Disassembly/assembly/change of sweeping brushes:
To enable access to the sweeping brush, the side cover of the
sweeping brush must be disassembled (pic. 17). Disassemble
the external carrying disk (pic.18 and 19). The brush and spacer
segments can now be individually removed (pic.20-22)
Cleaning
To clean/splash with water (especially using a high-pressure
cleaner):
lubricate all spots that need lubrication and let the sweeper run
for 1 to 2 minutes to allow water that has got inside to get away.
Clean the engine with just a cloth. Splash with strong current of
water as water can get in the ignition system, fuel system and
lubricating oil system, which may lead to failures.
Technical Data
Motor:
Output:
Capacity:
Tank capacity:
Operating width:
Ø sweeping roll:
Deflection angle:
Collection container
capacity:
Snow shield width:
Approximate weight:
Noise level:
Storing
If the sweeper has not been used for a long time, the following
steps need to be taken:
•
thorough cleaning and repair of damaged varnish
•
lubricating of spots that need lubrication and sweeper run
for 1 – 2 minutes
•
applying anti-corrosive oil on the sweeping brush and
chassis.
Putting the sweeper out of operation and storing
Do not transport the sweeper, put it out of operation and store
when tilted forward, backward or sideways.
Do not store the sweeper in damp rooms, in rooms where
fertilizers are stored, in stables or near them. Tilting may cause
the engine oil to get to the combustion space, which in
consequence may bring problems wit starting and oil
carbonization – risk of strong corrosion formation.
Briggs & Stratton
4.0 kW/5,5 PS at 3,600 a min
205 ccm
3.8 l
600 mm
350 mm
2 x 20°
capacity 60 l / max. 25 l of dirt
650 mm
70 kg
101 dB
-1