Applications; Setting The Transmission Channel - IMG STAGELINE TXS-606 Mode D'emploi

3 Applications

In combination with a wireless microphone, the
multi-frequency receiver TXS-606 provides a wire-
less audio transmission system ideally suited for
musicians and live applications on stage. The True
Diversity* receiver operates in the UHF frequency
range of 672.000 – 696.975 MHz. The frequency
for audio transmission is adjustable within this
range (frequency spacing: 25 kHz).
The following transmitters from "img Stage Line"
are suitable for combination with the TXS-606:
TXS-606HT Order No. 25.3540
Hand-held microphone with integrated multi-fre-
quency transmitter
TXS-606LT Order No. 25.3550
Multi-frequency pocket transmitter with tie clip
microphone
Frequency setting via the ACT function (automatic
channel targeting) is a most convenient feature:
Simply press a button to adjust the wireless micro-
phone / the pocket transmitter via IR signal to the
channel selected on the receiver.
* True Diversity technology
The signal coming from the wireless microphone
transmitter is received by two antennas and amplified in
two separate receiving parts. The signal offering the best
reception quality is then processed.
4 Operation
4.1 Connecting and
switching on the receiver
1) Connect the receiving antennas (2) provided to
the antenna jacks ANT A and ANT B (13). To lock
the antennas, turn the knurled ring of the plug
clockwise to the stop. Then set the antennas to
a vertical position.
To remove the antennas later, turn the ring
counter-clockwise first to unlock it.
2) Connect the receiver to the subsequent unit
(e. g. amplifier, mixer). For this purpose, two
audio outputs are provided:
MIC OUT (10) as an XLR jack, balanced
to connect a microphone input
LINE OUT (12) as a 6.3 mm jack, unbal.
to connect an input with line level; the output
level is adjustable (
3) Connect the power supply unit provided to the
power supply jack (9) and to a mains socket
(230 V~ / 50 Hz).
4) To switch on the receiver, press the button
POWER (8) until the display (3) lights up.
/
pocket
chapter 4.3)
To switch off later, press the button until the
display shows OFF. If the receiver is not in use
for a longer period of time, disconnect the power
supply unit of the receiver from the mains
socket; even with the receiver switched off, it
has a low power consumption.

4.2 Setting the transmission channel

To set a free transmission channel on the receiver,
either use the automatic search or the manual set-
ting. Then simply press a button to set the wireless
microphone / the pocket transmitter via IR signal to
the same channel.
1) For automatic search for a free receiving chan-
nel, press the button ACT (7) until the outer dis-
play elements of the numerals for GROUP and
CHANNEL start moving clockwise on the display.
After a while, the display shows the number of
the channel found. The corresponding frequen-
cies can be found in the table on pages 24 / 25.
2) For manual setting of a certain transmission
frequency, find the corresponding channel group
and channel number in the table on pages 24 / 25.
a) Press the button SET (4) once so that the
numerals for GROUP start flashing on the
display.
b) While the numerals keep flashing (a few sec-
onds after pressing the button SET,
set the channel group with the button
(5).
Note: If the numerals stop flashing before you have set
the group, press the button SET once again.
c) To set the channel number, press the button
SET repeatedly until the numerals for CHAN-
NEL start flashing.
d) Set the channel number with the button
. Once the numerals stop flashing, the
channel setting has been stored.
3) If the antenna symbol
the right of the display while the transmitter
(wireless microphone / pocket transmitter) is still
switched off, interfering signals or signals from
another wireless system are received. In this
case, set a different channel.
4) Switch on the transmitter and point the IR sen-
sor of the transmitter towards the IR window (6)
of the receiver (see instructing manual of the
transmitter, if required). The distance must not
exceed 1.5 m. Make sure that there are no
obstacles between the sensor and the IR win-
dow.
Briefly press the button ACT (7). The display
backlight of the transmitter is activated. Thus,
or
or
appears on the left or on
GB
),
or
9