Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2-Channel Receiver for
Wireless Microphones
These instructions are intended for users with-
out any specific technical knowledge . Please
read these instructions carefully prior to oper-
ating the unit and keep them for later refer-
ence . All operating elements and connections
de scribed can be found on the fold-out page 3 .
1 Operating Elements
and Connections
1.1 Front panel
1 Receiving antennas
2 Control section for receiver unit CH 1
3 Control section for receiver unit CH 2
4 Button POWER to switch on (press button
briefly) or off (keep button pressed for a
while)
5 Mounting bracket for rack installation of
the unit
6 Button REMOSET to set the transmitter to
the group and the channel of the receiver
unit
☞
chapter 6 .2
7 Button
to make settings in the different
setting modes
– to search in descending order when se-
lecting the group, the channel and the
identification number
– to deactivate the scan function
– to deactivate the lock function
8 Button SET
to activate the setting modes one after
another
group (keep button pressed for a while)
channel scan function identifi-
cation number lock function
and to confirm the settings
Note: When the lock function has been activated
[indication LOCK (e)], you will only be able to
activate the setting mode for the lock function
(
☞
chapter 6 .1 .4) .
9 Button
to make settings in the different
setting modes
– to search in ascending order when se-
lecting the group, the channel and the
identification number
– to activate the scan function
– to activate the lock function
10 LC display
a indication RF (radio frequency) for the
power of the radio signal received
b indication AF (audio frequency) for the
volume of the audio signal received
c diversity indication
A
which of the two antennas receives the
more powerful radio signal
d battery symbol to show the status of the
batteries in the transmitter in 4 levels
e indication LOCK when the lock function
has been activated
f indication MUTE when the muting func-
tion has been activated
muting activated when
– no radio signal is received from the
transmitter or when the signal is poor
– the transmitter has been muted
(possible for transmitter TXS-865HT
only)
g indication of the channel group
h indication of the channel
1.2 Rear panel
11 Audio outputs (XLR, bal .), one each for the
receiver units CH 1 and CH 2: to connect a
microphone input or highly sensitive line
input, e . g . of a mixer or amplifier
12 Squelch controls, one each for the receiver
units CH 1 and CH 2 to adjust the squelch
threshold
13 Switches, one each for the receiver units
CH 1 and CH 2, to attenuate the level of the
signal at the corresponding XLR output (11)
14 Audio output (6 .3 mm jack, bal .) for the
mixed signal of the receiver units CH 1 and
CH 2 for connection to a microphone input
or highly sensitive line input, e . g . of a mixer
or amplifier
15 Switch to attenuate the level of the mixed
signal at the 6 .3 mm output jack (14)
16 Power supply jack to connect the power
supply unit provided
17 BNC antenna jacks for the two antennas
(1) provided
2 Safety Notes
The units (receiver and power supply unit) cor-
respond to all relevant directives of the EU and
are therefore marked with
WARNING The power supply unit uses dan-
•
The units are suitable for indoor use only .
Protect them against dripping water and
splash water, high air humidity and heat
(admissible ambient temperature range:
0 – 40 °C) .
•
Do not operate the receiver and immediately
disconnect the power supply unit from the
socket
1 . if the units are visibly damaged,
2 . if a defect might have occurred after a
unit was dropped or suffered a similar
accident,
3 . if malfunctions occur .
In any case the units must be repaired by
skilled personnel .
•
For cleaning only use a dry, soft cloth; never
use water or chemicals .
•
No guarantee claims for the units and no
liability for any resulting personal damage or
material damage will be accepted if the units
are used for other purposes than originally
or
B
to show
intended, if they are not correctly connected
or operated, or if they are not repaired in an
expert way .
If the units are to be put out of oper-
ation definitively, take them to a local
recycling plant for a disposal which is
not harmful to the environment .
.
gerous mains voltage . Leave ser-
vicing to skilled personnel only .
Inexpert handling of the unit
may result in electric shock .
3 Applications
Combined with two transmitters of the TXS-
865 series from IMG STAGELINE, the multi-
frequency receiver TXS-865 creates a two-
channel wireless audio transmission system
ideally suited for professional stage applica-
tions . Both receiver units of the TXS-865 use
the diversity technology: The signal transmitted
is received by two antennas placed at a dis-
tance from each other and then checked for
its quality . The signal with the highest signal
quality will be used .
The transmission system operates in the
UHF range 506 – 542 MHz . Six channel groups
with preset channels in different numbers
(22 max .) are available . Frequency matching is
very easy: Via a radio signal, the receiver unit
will set the transmitter to the same transmis-
sion frequency (REMOSET function) .
3.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare
that the receiver TXS-865 complies with the
directive 2014/53/EU . The EU declaration of
conformity is available on the Internet:
www .imagestageline .com
The receiver may be operated in the following
countries:
DE
The corresponding transmitters require regis-
tration; please refer to the instruction manuals
of the transmitters!
4 Rack Installation
Either use the receiver as a desktop unit or
install it into a rack for units with a width of
482 mm (19") . For rack installation, unscrew
the four feet . Fasten the two mounting brack-
ets (5) provided via two screws each to the left
and right sides of the receiver .
5 Connection
1) Insert the two antennas (1) provided into
the antenna jacks ANT . 1 and ANT . 2 (17) .
Place the antennas in a vertical position .
Hint: The pair of antenna signal amplifiers TXS-
875B (available as an accessory) can be used to
increase the transmission range and the interfer-
ence resistance . The amplifiers are supplied with
power via the antenna jacks of the receiver .
2) To connect the subsequent unit, e . g . mixer
or amplifier, the following audio outputs
are available:
AF OUTPUT BAL . (11)
balanced XLR outputs, one each for the
signal of the receiver unit CH 1 and the
signal of the receiver unit CH 2, for con-
nection to a microphone input or highly
sensitive line input
AF OUTPUT MIXED / BAL . (14)
balanced 6 .3 mm output jack for the
mixed signal of the two receiver units,
for connection to a microphone input or
a highly sensitive line input;
for connection to an unbalanced input,
use the cable provided
3) Connect the power supply unit provided to
the power supply jack (16) and to a mains
socket (230 V/ 50 Hz) .
7
Publicité
Table des Matières
