Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
installation
7. Safety
only a qualified contractor should
carry out installation, commission-
ing, maintenance and repair of the
appliance.
7.1 General safety instruc-
tions
We guarantee trouble-free operation
and operational reliability only if the
original accessories and spare parts
intended for the appliance are used.
7.2 Regulations, standards
and instructions
D ANGER Electrocution
Carry out all electrical con-
nection and installation
work in accordance with relevant
regulations.
D amage to the appliance
!
and environment
observe the type plate. the
specified voltage must match the
mains voltage.
N ote
observe all applicable na-
tional and regional regula-
tions and instructions.
8. Appliance descrip-
tion
8.1 Standard delivery
delivered with the appliance:
- 1 wall mounting bracket
- 1 locking tab
- 2 screws
- 2 rawl plugs
Guarantee
For guarantees please refer to the respective terms and conditions of supply for your country.
The installation, electrical connection and first operation of this appliance should be carried out by a qualified
!
installer.
The company does not accept liability for failure of any goods supplied which have not been installed and
!
operated inaccordance with the manufacturer's instructions.
Environment and recycling
Recycling of obselete appliances
Appliances with this label must not be disposed off with the general waste. They must be collected separately and disposed off
according to local regulations.
9. Preparations
9.1 Installation in bath-
rooms
D ANGER Electrocution
Install the appliance ex-
clusively outside safety
zone 2.
C
0
safety zone 0
1
safety zone 1
2
safety zone 2
3
safety zone 3
f ensure that you maintain the
f
safety clearances of safety
zone 2 towards bath tubs, show-
er cubicles and washbasins.
9.2 Installation site
DANGER Fire
fensure that the wall on
which the appliance is
mounted is resistant to tempera-
tures up to at least 90 °c.
f ensure that the installation site is
f
not below a socket.
f ensure that the installation site is
f
at least 10 cm away (to the side)
from a socket.
9.3 Minimum clearances
A
f ensure that the minimum per-
f
missible clearances to adjacent
objects are maintained.
f ensure that the hot air can es-
f
cape from the appliance without
obstruction.
10. Mounting
D
1 locking tab
2 Wall mounting bracket
3 latching stay
f secure the wall mounting brack-
f
et to the wall with suitable rawl
plugs and screws.
f offer the back of the appliance
f
to the wall mounting bracket
and guide the apertures in the
appliance back over the latch-
ing stays in the wall mounting
bracket.
f push the appliance down so that
f
it sits fully on the wall mounting
bracket.
f insert the locking tab into the
f
top aperture of the wall mount-
ing bracket.
f turn the locking tab with a
f
screwdriver until it clicks into
place.
10.1 Power supply
f connect the appliance to the
f
power supply with the mains
plug supplied.
11. Specification
11.1 Dimensions and connec-
tions
E
b01
entry electrical cables
i13
Wall mounting bracket
11.2 Wiring diagram
F
r1 electric heating element
n1 temperature controller
F1 safety temperature controller
11.3 Data table
Electrical data
connected load
power supply
Dimensions
height
Width
depth
Weight
Weight
Versions
Frost protection setting
ip rating
safety category
colour
Values
setting range
CFK 5
073685
kW
0.5
1/n ~ 230 v
mm
387
mm
170
mm
110
kg
1.2
°c
6
ip20
ii
white
°c
6-45
cFK 5 | 9
Publicité
Table des Matières
