Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1
/
full with cold fresh milk.
light will start to flash indicating that the
3
NOTE: When the 800ESXL is
Thermoblock Heating System is heating
and preparing to create steam.
creating steam a pulsing
noise can be heard. This is
the normal operation of the
NOTE: If steam starts coming
from
the Steam Wand before it is
immersed in the milk, pause
the steam by turning the
Selector Control back to the
'Standby' position. This
will avoid the steam
pressure blowing milk out
NOTE: The 800ESXL features a
•
Turn the Selector Control to the 'Steam'
position and press the 'Steam' button.
(Refer to information on Steam and Hot
Water buttons on Page 19.) The
'Heating'
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ
1 8
•
When the red 'Heating' light stops
flashing, quickly insert the Steam Wand
into the jug of milk so that the Froth
Attachment is just immersed into the
milk.
Swivel Steam Wand
assembly so
the position of the Steam
Wand can be changed to a
•
When the milk starts to increase in
volume, immerse the Frothing
NOTE:
Always ensure that the
Attachment deeper into the jug to heat
Frothing Attachment has
the milk.
been firmly pushed onto the
Steam Wand and connects
•
Hold the jug at an angle with one hand
and place your other hand on the outer
with the rubber surround.
base of the stainless frothing jug.
For best results use cold
•
When the base of the jug becomes too
fresh milk (low fat milk will
hot to touch, set the Selector Control to
froth easier) .
the 'Standby' position, stopping the
Always clean the Steam
steaming function before removing the
Wand and Frothing
jug. A pumping noise will sound for a
short time.
Attachment after every
•
Pour the steamed milk into each cup of
freshly brewed espresso coffee and
•
Hold the frothing jug at an angle so that
spoon in the frothed milk, in the
the Frothing Attachment sits just below
following ratios: Cappuccino -
the surface of the heating milk and the
espresso,
steam will move the milk around the
1
/
frothed milk
inside of the jug in a circular motion.
3
Latté -
1
/
3
steamed milk and about 1cm of frothed
milk (traditionally served in a glass)
CAUTION: DO NOT ALLOW MILK TO RUN OVER THE TOP OF THE FROTHING ATTACHMENT, OTHERWISE IT
WILL NOT FUNCTION PROPERLY.
TO AVOID SPLATTERING OF HOT MILK, DO NOT LIFT THE END OF THE FROTHING ATTACHMENT
ABOVE THE SURFACE OF THE MILK WHILE FROTHING.
ENSURE THE SELECTOR CONTROL IS IN THE 'STANDBY' POSITION BEFORE REMOVING THE
STEAM BUTTON/HOT WATER BUTTON
•
The Steam button surround will
automatically illuminate when the
machine is switched 'On' with the Power
On/Off button.
•
The machine will always automatically
default to the Steam button when the
appliance is first switched on.
•
Both buttons cannot be operated at the
same time.
•
To select steam: when the Steam button
surround is illuminated, just set the
Selector Control to 'Steam'
•
To select hot water: press the Hot
Water button and the surround will
illuminate, then just set the Selector
1
/
3
Control to 'Steam'.
/
steamed milk,
1
3
•
If the machine remains switched 'On',
espresso topped with
the last button function used (Steam or
Hot Water) will stay illuminated.
HOW TO FROTH MILK FOR A CAPPUCCINO OR LATTÉ
1 9
Publicité
Chapitres
Table des Matières
