Description And Specifications - Franklin Electric I Serie Manuel D'installation, De Fonctionnement Et De Maintenance

DESCRIPTION AND SPECIFICATIONS

The I-Series are single-stage, end suction, centrifugal pumps
for general liquid transfer, booster applications, irrigations, and
general service pumping.
Pump impellers are fully enclosed, key-driven, and held in position
by an impeller bolt and washer. Casings are full volute in design.
Based on the diversity of applications and requirements within which the I-Series pumps are installed, the configurations, materials of
construction, and specifications may significantly vary within the models available. Therefore it is the responsibility of the installer and
customer to confirm the model of pump and reference catalog information accordingly to identify the specifics of the unit prior to installation.
Additionally, assistance is available from a Franklin Distributor or by calling the Franklin Hotline.
I-Series
SIZE DISCHARGE
1 x 1-1/2 - 6 1-1/4" NPT
1-1/2 x 2 - 6 1-1/2" NPT
3 x 4 - 6 3" NPT
1-1/2 x 2 - 8 1-1/2" NPT
2 x 3 - 8 2" NPT
3 x 4 - 9 3" VIC
3 x 4 - 9 3" NPT
4 x 4 - 9 4" NPT
4 x 5 - 9 4" Flange
6 x 8 - 9 6" Flange
2 x 3 - 10 2" Flange
2-1/2 x 4 - 10 2-1/2" Flange
3 x 4 - 10 3" Flange
4 x 6 - 10 4" Flange
6 x 8 - 10L 6" Flange
6 x 8 - 10 6" Flange
2-1/2 x 3 - 13 2-1/2" Flange
3 x 4 - 13 3" Flange
4 x 6 - 13 4" Flange
6 x 8 - 13 6" Flange
8 x 10 - 13 8" Flange
3 x 5 - 14 3" Flange
4 x 6 - 14 4" Flange
6 x 6 - 14 6" Flange
6 x 8 - 14 6" Flange
10 x 10 - 14 10" Flange
Dependent on the pump size, the suction and discharge
connections will be threaded, flanged or victaulic. Shafts are
protected with replaceable shaft sleeves.
Close-coupled units have NEMA-standard JP motors with C-face
mounting and key-driven shaft extension. SAE drive units bolt
directly to the engine flywheel housing for SAE sizes 1, 2, 3, 4 or 5.
Optional elastomer element couplings are available for 6.5-,
7.5-, 8-, 10-, 11.5-, and 14-inch flywheels. Frame-mounted units
can be coupled to motors through a shaft-to-shaft coupling, or
belt-driven.
SUCTION IMPELLER MATERIAL
1-1/2" NPT Bronze
2" NPT Bronze
4" NPT Cast Iron
2" NPT Bronze
3" NPT Bronze
4" VIC Cast Iron
3" NPT Cast Iron
4" NPT Epoxy Cast Iron
5" Flange Epoxy Cast Iron
8" Flange Cast Iron
3" Flange Ductile Iron
4" Flange Ductile Iron
4" Flange Ductile Iron
6" Flange Ductile Iron
8" Flange Ductile Iron
8" Flange Ductile Iron
3" Flange Stainless Steel
4" Flange Stainless Steel
6" Flange Stainless Steel
8" Flange Stainless Steel
10" Flange Stainless Steel
5" Flange Ductile Iron
6" Flange Ductile Iron
6" Flange Ductile Iron
8" Flange Ductile Iron
10" Flange Ductile Iron
HYDRAULIC BALANCE
n/a
n/a
n/a
n/a
n/a
Balance Holes
Balance Holes
External Line
External Line
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
Balance Holes
External Line
External Line
3