Panel Mounting; Technical Specifications - Tyco PowerSeries Neo TL280LE Mode D'emploi

work. TL2803G(R)E: Is a dual-path HSPA(3G) Ethernet alarm communicator that sends alarm communication to Sur- Gard
System -IPI, II, III, IV, and 5 central station receivers through Ethernet/Internet or a HSPA(3G)/GPRS digital cellular network.
TL280(R) E : Is an Ethernet alarm communicator that sends alarm communication to Sur- Gard System I- IP, II, III (SG-
DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers via Ethernet/Internet.
LE2080(R): is an LTE (4G) cellular alarm communicator with HSPA(3G) fallback support that sends alarm communications
to Sur- Gard System I- IP, II, III (SG- DRL2IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers via an LTE(4)
/HSPA(3G) digital cellular network.
TL280LER: Is a dual path LTE (4G) Ethernet alarm communicator that sends alarm communications to Sur-Gard System I-
IP, II, III (SG-DRL3IP, IV (SG-DRL4IP) and 5 (SG-DRL5IP) central station receivers via Ethernet/Internet or a LTE(4)/HSPA
(3G) digital cellular network.
The communicator can be used as either a backup or primary communicator. The communicator supports Internet Protocol
(IP) transmission of panel and communicator events over Ethernet/Internet and/or HSPA/GPRS.
The cellular performance of the LE2080(R), TL280LE(R), 3G2080(R) E or TL2803G(R) E communicators depend greatly
on the LTE(4G)/HSPA(3G) network coverage in the local area. The unit should not be mounted in the final location without
first performing the communicator placement test below to determine the best location for radio reception (minimum of one
green LED ON). Optional antenna kits (GS-15ANTQ, GS-25ANTQ, GS- 50ANTQ) are available from DSC to improve sig-
nal strength as required.
NOTE: Prior to installation, confirm with the local service provider that the network is available and active in the area where
the communicator will be installed, and that radio signal strength (CSQ) is adequate.
The following communicators are compatible with HS2016, HS2016-4, HS2032, HS2064, and HS2128 panels:
3G2080(R)E
(HSPA(3G)/GPRS only)
l
TL2803G(R)E
(Ethernet/Internet + HSPA(3G)/GPRS dual-path)
l
TL280(R)E
(Ethernet/Internet only)
l
LE2080(R) (LTE(4G)/HSPA(3G) only)
l
TL280LE(R) (Ethernet/Internet + LTE(4G)/HSPA(3G))
l
128-bit AES encryption via cellular and Ethernet/Internet
l
- NIST validation cert number 2645 (for models TL2803G(R)E/3G2080(R)E/TL280(R)E
- NIST validation cert number 4475 (for models TL280LE(R)/LE2080(R))
Backup or primary cellular alarm communication.
l
Automatically switches to 2G (EDGE/GPRS) if HSPA(3G) service is not available (2G not supported on LTE models).
l
Automatically switches from LTE to HSPA(3G) service if LTE service is not available.
l
Ethernet LAN/WAN 10/100 BASE-T (TL2803G(R)E, TL280(R)E, TL280LE(R) only).
l
Fully redundant Ethernet/Internet and cellular dual-path alarm communication (TL2803G(R)E, TL280LE(R) only).
l
Full event reporting to central station.
l
Individual Internet and/or cellular periodic test transmission.
l
Integrated call routing.
l
Visual Verification (Requires Sur-Gard System 5 Receiver)
l
Remote firmware upgrade capability of the communicator and panel firmware via Ethernet and/or cellular.
l
Panel remote uploading/downloading support via cellular and Ethernet/Internet.
l
PC-LINK connection.
l
Programmable labels.
l
SIA and Contact ID (CID) formats supported.
l
Signal strength and trouble display LEDs.
l
Supervision heartbeats sent via cellular and Ethernet/Internet.
l
Third party integration over cellular/IP. The product supports third-party application via serial (R-models only), cellular
l
and, Ethernet. Refer to third-party application documentation for more information.
NOTE: RS-232 connection is for supplementary use only and was not evaluated by UL/ULC.
The TL2803G(R)E/TL280LE(R) are also suitable to be used with a compatible control unit listed for dual line security trans-
mission when used in conjunction with a DACT or a Public Switched Data Network (PSDN) transmitter, where the PSDN
provides the line security and is the primary line. In this mode, alarm signals are to be sent simultaneously over both com-
munication methods.

Panel Mounting

Features

Technical Specifications

4