Table Des Matières; Pre-Installation - Pentair PRO-SOURCE 8MM05231 Notice D'utilisation

Carefully read and follow all safety instructions
in this manual or on pump.
This is the safety-alert. When you see
this symbol on your pump or in this
manual, look for one of the following signal
words and be alert to the potential for personal
injury.
warns about hazards that will
cause serious personal injury, death or major
property damage if ignored.
warns about hazards that can
cause serious personal injury, death or major
property damage if ignored.
warns about hazards that will or
can cause minor personal injury or property
damage if ignored.
The word NOTICE indicates special instructions
which are important but not related to hazards.
To avoid serious or fatal personal injury and
possible property damage, carefully read and
follow the safety instructions.
Hazardous pressure. Under
1.
certain conditions, submersible pumps can
develop extremely high pressure. Install a
pressure relief valve capable of passing entire
pump flow at 75 PSI (517 kPa) when using an air
over water pressure tank. Install a pressure relief
valve capable of passing entire pump flow at 100
PSI (690 kPa) when using a pre-charged pressure
tank.
Do not allow pump, pressure tank,
piping, or any other system
component containing water to freeze.
Freezing may damage system, leading to
injury or flooding. Allowing pump or
system components to freeze will void
warranty.
2. Hazardous voltage. Can shock,
burn or cause death. To avoid
dangerous or fatal electric shock hazard, use
pump only in a water well.
Risk of dangerous or fatal
electrical shock. Do not install this pump in
any pond, river, or other open body of water
that could be used for swimming or
recreation. Do not swim, wade or play in a
body of water in which a submersible pump
has been installed.
Installation must meet United States
National Electrical Code, Canadian Electrical
Code, and local codes (as applicable) for all
wiring.
Disconnect electrical power supply
before installing or servicing pump.
Make sure line voltage and frequency of
power supply match motor nameplate voltage
and frequency.
3. Install pump according to all plumbing, pump
and well code requirements.
4. Test well water for purity before using well.
Call your local health department for testing
procedure.
5. During installation, keep well covered as
much as possible to prevent leaves and foreign
matter from falling into well. Foreign objects
in well can contaminate the water and cause
serious mechanical damage to the pump.
6. Pipe joint compound can cause cracking in
plastics. Use only teflon tape when sealing
joints in plastic pipe or connecting pipe to
thermoplastic pumps.
TABLE OF CONTENTS
Safety Instructions . . . . . . . . . . . . . . . . . . . . . .2
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . .2
Electrical-General . . . . . . . . . . . . . . . . . . . .2-3
60 Hz Fuse, Wire, Motor Specs.
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . .5-6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
Initial Startup . . . . . . . . . . . . . . . . . . . . . . . .8-9
Connecting to Tank/Water System . . . . . . .9-11
Troubleshooting Guide . . . . . . . . . . . . . .12-13
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

PRE-INSTALLATION

Inspect pump and motor for delivery damage.
Report any damage immediately to the shipping
carrier or to your dealer.
The well driller should thoroughly develop the
well (that is, pump out all fine sand and foreign
matter) before pump is installed.
Pump performance is based on pumping clear,
cold, liquid water.
Warranty is void in the following conditions:
• If pump has pumped excessive sand -
excessive sand can cause premature wear to
pump.
• If water is corrosive.
• If entrained gas or air are present in the water
being pumped - these can reduce flow and
cause cavitation which can damage pump.
• If pump has been operated with discharge
valve closed - severe internal damage will
result.
Install pump at least 15 to 20' (4.5 to 6M) below
the lowest water level reached with pump
running (lowest draw-down water level), and at
least 5' (1.5M) above the bottom of the well.
WIRING/GROUNDING:
Hazardous voltage. Can shock,
burn, or cause death. Permanently ground
pump, motor and control box before
connecting power supply to motor.
Ground pump and motor in accordance with the
local codes and ordinances. Use a copper
ground wire at least as large as wires carrying
current to motor.
2
. . . . . . . . . .4