Reversibility Of A Glass Door - Eurocave 5000 Série Mode D'emploi

4/ INSTALLING YOUR WINE CABINET
Changing the hinges
1
Loosen the three screws using the Torx "T25" tool.
2
Remove the upper hinge.
3
Remove the grommets gently using a fine blade.
Precautions: If you lift off the glass door of the cabinet, never place it
on its edges which may cause it to break.
Adjusting the mounting feet and attachment (only when the cabinet is empty)
•
The 4 feet of the wine cabinet are adjustable in height so that the height
below the work surface orin the unit can be adjusted, and to align the
door with adjacent furniture.
1
•
If necessary, use the hexagonalpillars that you will find in the
"accessories" bag.
•
Tilt the unit forward, taking care to keepthe door closed.
•
Unscrew the rear feet and install the pillars, using a 17 mm flat spanner.
•
Screw the 2 rear feet back onto the pillars.
2
3
•
Repeat these operations for the 2 front feet, taking good care to tilt the
unit backwards.
Never obstruct the front ventilation grille which would impair the
operation of the wine cabinet
10
GB
B
•
Fit the hinge with pin using the screws so that the door is parallel
to the cabinet.
A
•
Fit the hinge without pin with the screws.
1
2
3
Precautions: When closing the door, check that the seal adheres
correctly to the cabinet so that it is airtight.
•
Use the correct screws to secure the wine cabinet under the work
surface or in the unit through the holes provided in the hinges.
Precautions: on the side of the axis of rotation of the door,positionthe
latter a minimum of 3 mm from adjacent furniture.
The mains power socket must be accessible after installation of
the unit.
For medium and large models, it is essential to secure the
cabinet to the wall to prevent it from tipping forward. Have
your cabinet checked by a professional to confirm that it is fixed
to the furniture and that the furniture is fixed to the wall.
Installing a cabinet within a high level kitchen unit
For safety reasons, we do not advise installing the wine cabinet
in a kitchen unit.
If this is the case, check with a furniture specialist that the unit
supporting the equipment and the surrounding furniture can
support the weight of the cabinet when filled with full bottles,
or 200 kg. Have its stability checked by this specialist when
opening the door and removing shelves loaded with full bottles.
1I. Reversibility of a glass door
5
B
4
A
7 You can change which way it opens. Proceed as follows (example for
changing a right hand door to a left hand door):
A
6
3 min.
4
1
Loosen the three screws using the Torx "T25" tool.
2
Remove the upper hinge.
3
Remove the grommets gently using a fine blade.
4
Lift the door from the lower hinge by opening the door slightly and
then lifting it.
6
5
Loosen the door pivot guide.
6
Remove the grommets gently using a fine blade and in its place fit the
pin. Relocate the grommet on the opposite side.
7
Loosen the four screws.
8
Locate the foot on the other side of the housing using the screws.
4/ INSTALLING YOUR WINE CABINET
x3 x3 x6 x2
B C D E F G H J
1
2
3
9
Turn the door 180°.
10
Replace the door on its pivot guide.
5
8
11
Relocate the upper hinge.
12
7
Relocate the hinge in such a way so that the door is parallel with the
case. Check (by closing the door) that the seal adheres well to the
housing and is leak proof.
13
Replace the grommets.
A G
Upper hinge Lower hinge
B H
Grommets Door pivot guide
C J
Grommets Door axis plug
D
Torx screw
E
Torx screw
F
Closing clip
9
Warning: the glazed doors are very heavy. Take all necessary
precautions not to injure yourself or drop the door.
13
12
11
11
GB