Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TIG - MMA WITH POWER UNIT
Figure 36 - Save & Recall Views for MMA/TIG
Save & Recall Key
4
Use the Save & Recall Key to save and recall the pa-
rameters set by the operator. The available memories
are 10.
To save the parameters proceed as follows:
•
Press the Save & Recall Key - 4 -
•
Turn the Right Regulation knob - 5 - to choo-
se the program number to save in.
•
To save the program push the SAVE Key - 6 -
To recall a saved program proceed as follows:
•
Press the Save & Recall Key - 4 -
•
Turn the Right Regulation knob - 5 - to choo-
se the desired program number.
•
Press the LOAD Key - 8 -.
MIG MAG WITH POWER UNIT
Figure 37 - Save & Recall Views for MIG/MAG
4
Save & Recall Key
Use the Save & Recall Key to save and recall the pa-
rameters set by the operator. The available memories
are 250.
To save the parameters proceed as follows:
•
Press the Save & Recall Key - 4 -
•
press - 6 - to enter in memory selection (ALL
POINTS)
•
Next screen is Operator Point.
•
Turn the Right Regulation knob - 5 - to choo-
se the program number to save in.
•
To save the program push the SAVE Key - 6 -.
•
To add the operator point in the working list
press - 3 - (ADD W.L.).
•
Turn the Right Regulation knob - 5 - to choo-
se the program number to save in.
•
To save the program into the working list push
the SAVE Key - 6 -.
To recall a saved program proceed as follows:
•
Press the Save & Recall Key - 4 -
EN-30
SAVE & RECALL
•
press - 6 - to enter in memory selection (ALL
POINTS)
•
Turn the Right Regulation knob - 5 - to choo-
se the required program number
•
Press the LOAD Key - 8 -
WORKING LIST WITH POWER UNIT
(ONLY FOR MIG/MAG)
Figure 38 - Working List View
The user can select up to 20 memories and place
them in the working list.
To save the parameters directly proceed as follows:
•
Press the Save & Recall Key - 4 -
•
press - 8 - to enter in the working list (WOR-
KING LIST)
•
Next screen is the Working List.
•
Turn the Right Regulation knob - 5 - to choo-
se the program number to save in.
•
press - 3 - (EDIT) to enter in the operator
point memory selection
•
Turn the Right Regulation knob - 5 - to choo-
se the program number to add to the working
list
•
press - 3 - (ADD W.L.) to add the parameters
to the selected memory of working list
•
To save the working list point push the SAVE
Key - 6 -
To recall a saved operetor point into the working list
proceed as follows:
•
Press the Save & Recall Key - 4 -
•
press - 8 - to enter in the working list selec-
tion (WORKING LIST)
•
Turn the Right Regulation knob - 5 - to choo-
se the required program number.
•
Press the LOAD Key - 8 -
To delete a saved operetor point into the working list
proceed as follows:
•
Press the Save & Recall Key - 4 -
•
press - 8 - to enter in the working list selec-
tion (WORKING LIST)
•
Turn the Right Regulation knob - 5 - to choo-
se the required program number.
•
Press the DEL Key - 6 -
To exit SAVE & RECALL mode press MODE key - 1
- till you reach your required welding process menu
Publicité
Chapitres
Table des Matières
