FALMEC Piano Mode D'emploi page 43

Masquer les pouces Voir aussi pour Piano:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 57
SAFETY INSTRUCTIONS AND WARNINGS
INSTALLATION WARNINGS
TECHNICAL SAFETY
Installation operations are to be carried out
by skilled and qualified installers in accord-
ance with the instructions in this booklet
and in compliance with the regulations in force.
• Before installing the hood, check the integrity
and function of each part. Should anomalies
be noted, do not proceed with installation and
contact the Dealer.
• Do NOT install the hood if an aesthetic defect
has been detected. Put it back into its original
package and contact the dealer. No claim can
be made for aesthetic defects once the hood
has been installed.
• During installation, always use personal protective
equipment (e.g. accident-prevention shoes) and
adopt prudent and proper conduct.
• Keep in mind that installations with different types
of fixing systems from those supplied, or which are
not compliant, can cause electrical and mechanical
seal danger.
• Do not modify the electrical, mechanical and func-
tional structure of the equipment.
• Do the install the hood outdoors and do not expose
it to atmospheric agents (rain, wind, etc.).
• After the stainless steel hood has been installed,
it will need to be cleaned to remove any residues
from the protection adhesive as well as any grease
and oil stains which, if not removed, can cause ir-
reversible damage to the hood surface. To do so
the manufacturer recommends using the supplied
moist wipes, which are also available sold separate-
ly.
ELECTRICAL SAFETY
The electrical system to which the hood is
to be connected must be according to
standard and compulsorily supplied with
earthed connection in compliance with safety
regulations in the country of use. It must also
comply with European standards regarding radio
antistatic properties.
• Before installing the hood, check that the electrical
mains power supply corresponds with what is re-
ported on the identification plate located inside the
hood.
• The socket used to connect the installed equip-
ment to the electrical power supply must be within
reach: if this is not possible, install a mains switch
in an accessible position in order to disconnect the
hood when required.
• Any changes to the electrical system required to
install the hood must be carried out by a qualified
electrician.
• It is dangerous to change, or try to change, the
features of this equipment. Do not try to solve the
problem yourself in the event of equipment mal-
function, but contact the Dealer or an authorised
Servicing Department for repairs.
• If the power cable needs to be replaced by the
Technical Servicing Department, use a H05VV-F
type cable with 3x0.75mm² section.
• When installing the hood, disconnect the equip-
ment by removing the plug or switching off the
main switch.
FUMES DISCHARGE SAFETY
• Do not connect the equipment to discharge
pipes of fumes produced from combustion (for
example boilers, fireplaces, etc.)
• Before installing the hood, ensure that all standards
in force regarding discharge of air out of the room
have been complied with.
USER WARNINGS
GENERAL WARNINGS
These warnings have been drawn up for
your personal safety and those of others.
You are therefore kindly asked to read the
booklet carefully in its entirety before installing
and using the equipment or carrying out cleaning
operations.
• The Manufacturer declines all responsibility for
any damage caused directly, or indirectly, to
persons, things and pets as a consequence of
failing to comply with the safety warnings indi-
cated in this booklet.
• It is imperative that this instructions booklet is
kept together with the equipment for any fu-
ture consultation. If the equipment is sold or
transferred to another person, make sure that
the booklet is also supplied so that the new user
can be made aware of the hood's operation and
relative warnings.
• Installation operations are to be carried out by
skilled and qualified installers in accordance with
the instructions in this booklet and in compliance
with the regulations in force.
• DO NOT use the hood if the power supply cable
or other components are damaged. Disconnect
the hood from the electrical power supply and con-
tact the Dealer or an authorised Servicing Depart-
ment for repairs. Insist on original spare parts. Do
not personally try to carry out repairs or replace-
ments. Interventions carried out by incompetent
and unauthorised persons can cause damage, even
serious, to things and/or persons not covered by
the Manufacturer's warranty.
• Do not modify the electrical, mechanical and func-
tional structure of the equipment. Any changes to
the electrical system required to install the hood
must be carried out by a qualified electrician.
43

Publicité

Table des Matières
loading

Table des Matières