General Safety Warnings - Dremel 3D40 Traduction De La Notice Originale

GB
ORIGINAL INSTRUCTIONS

GENERAL SAFETY WARNINGS

WARNING
!
MANUAL AND FAMILIARIZE YOURSELF
WITH THE DREMEL 3D40 BEFORE SETUP
AND USE. FAILURE TO COMPLY WITH THE
WARNINGS AND INSTRUCTIONS MAY RESULT IN
FIRE, EQUIPMENT DAMAGE, PROPERTY DAMAGE,
OR PERSONAL INJURY. SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE REFERENCE
WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate Dremel 3D40 in the presence of
flammable liquids, gases or dust. Dremel 3D40
creates high temperatures which may ignite the
dust or fumes.
c. Store idle 3D40s out of reach of children and
other untrained persons. Injury can occur in
hands of untrained users.
ELECTRICAL SAFETY
a. Always use the Dremel 3D40 with a properly
grounded outlet. Do not modify Dremel 3D40
plug. Improper grounding and modified plugs
increase risk of electric shock.
b. Do not use Dremel 3D40 in damp or wet
locations. Do not expose Dremel 3D40 to rain.
Presence of moisture increases risk of electric
shock.
c. Do not abuse the cord. Never use the cord for
pulling or unplugging the Dremel 3D40.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
d. Avoid using this product during an electric
storm. There may be a remote risk of a power
surge from lightning that may result in an electric
shock.
e. In case of emergency unplug Dremel 3D40 from
outlet.
PERSONAL SAFETY
a. Stay alert, watch what you are doing and
use common sense when operating a Dremel
3D40. Do not use Dremel 3D40 while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating Dremel 3D40 may result in personal
injury.
b. Use personal protective equipment. The use of
protective equipment such as heat resistant gloves
and safety glasses will reduce the risk of personal
injuries.
c. Dress properly. Do not wear loose clothing or
Jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, Jewellery
or long hair can be caught in moving parts.
DREMEL 3D40 USE AND CARE
a. Before every use check Dremel 3D40 for
misalignment or binding of moving parts,
breakage of parts and any other condition
READ ALL
INSTRUCTIONS IN THIS
2
that may affect the Dremel 3D40's operation.
If damage is suspected then have the Dremel
3D40 repaired by an authorised Dremel service
centre before use. Use of Dremel 3D40 when
damaged may result in poor quality of object
creation, further equipment damage, property
damage or personal injury.
b. Do not touch the extruder tip during Dremel
3D40 operation or until it has cooled down to
at least 60°C (140°F). Contact with the extruder tip
during or after operation before tip has cooled may
result in personal injury.
c. Set up the Dremel 3D40 in a well-ventilated
area. Provide at least 8 inches of unobstructed
spacing around Dremel 3D40. Dremel 3D40
melts plastic during building. Plastic odours emitted
during Dremel 3D40 operation may irritate eyes
and airways. Locating Dremel 3D40 close to
surrounding objects prevents proper ventilation.
d. Do not reach inside the Dremel 3D40 while it is
in operation. Contact with Dremel 3D40 moving
parts during operation may result in poor build
quality, equipment damage or personal injury.
e. Do not leave the Dremel 3D40 unattended
during operation. Use of Dremel 3D40 by persons
unfamiliar with these warnings and instructions may
result equipment or property damage and personal
injury.
f. Use only DREMEL PLA filament. Use of filament
not authorized by Dremel may result in equipment
and property damage.
g. Ensure small objects created by Dremel 3D40
are not accessible to young children. Small
objects are potential choking hazards for young
children.
h. Do not create illegal or inappropriate objects
using Dremel 3D40.
i. Do not use Dremel 3D40 to create objects
intended for use with candles, liquid fuels,
and other heat sources. Plastic may melt when
exposed to fire or other heat sources. Such use of
objects created by Dremel 3D40 may result in fire,
property damage and personal injury.
j. Do not use Dremel 3D40 to create objects
intended for food or drink applications
such as preparation, decoration, storage, or
consumption. Such use of objects created by
Dremel 3D40 may result in illness or personal
injury.
k. Do not use Dremel 3D40 to create objects
intended with use with electrical components or
housings of electrical components. PLA plastic
is not suitable for electrical applications. Such use
of objects created by Dremel 3D40 may result in
property damage and personal injury.
l. Do not put plastic objects in or around your
mouth. PLA plastic is not suitable for food or drink
preparation and food utensils. Such use of objects
created by Dremel 3D40 may result in illness or
personal injury.
m. Do not use Dremel 3D40 to create objects
intended for chemical storage. PLA plastic is not
suitable for chemical storage. Such use of objects
created by Dremel 3D40 may result in property
damage and personal injury.
n. Do not modify Dremel 3D40 or alter factory
settings. Modifications may result in equipment
and property damage, and personal injury.
o. Do not expose Dremel 3D40 to temperatures
exceeding 70°C (158°F). Dremel 3D40 may
become damaged. Dremel 3D40 is intended to
operate in temperature between 16-29° C
(60 - 85° F).