Checking Blade Wear; Sharpening The Mowing Blade; Removing And Installing The; Mowing Blade - Stihl RM 2 R Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 49
● Lift up the machine at the front and
place in the cleaning position as shown.

12.2 Checking blade wear

Maintenance interval:
Before each use.
Risk of injury!
Blades are subjected to differing
degrees of wear depending on the
location and duration of use. If you
use the machine on sandy ground
or use it frequently under dry
conditions, the blade will be
subjected to greater loads and will
wear more quickly than the
average.
A worn blade may break off and
cause serious injuries. The
instructions for blade maintenance
must therefore always be
observed.
Checking procedure
● Place the machine in the cleaning
position. (
12.1)
● Clean the blade (1) and check it for
damage (notches or cracks).
● Use a slide calliper (2) to measure the
blade thickness (A) at several points.
● Measure the permissible grinding (B).
Place a ruler (3) against the front blade
edge as shown for this purpose.
Wear limits
The blade thickness (A) must be at least
2 mm at any point. The most important
points are marked in the illustration.
The cutting edges must not be ground
back by more than 5 mm – distance (B)
(permissible grinding) during sharpening.
40

12.3 Sharpening the mowing blade

If you do not have the necessary expertise
or auxiliary equipment, we recommend
that you have the blade sharpened by a
13
specialist dealer. Operation of the machine
is impaired in the case of an incorrectly
sharpened blade (incorrect sharpening
angle, imbalance etc.).
Sharpening instructions
● Remove the mowing blade. (
● Cool the mowing blade during
sharpening, e.g. with water.
The blade must not be allowed to
display blue colouring, as this would
reduce its cutting quality.
● Sharpen blades evenly to prevent
vibration due to imbalance.
● Observe a sharpening angle of 30°.
● Observe the wear limits (

12.4 Removing and installing the

mowing blade

Risk of injury!
Always wear gloves.
The mowing blade must
be replaced if notches or
cracks are detected or if a wear
limit is reached (
Removing
● Hold the mowing blade (1) and loosen
the blade fastening screw (2).
● Remove the blade fastening screw (2),
retaining washer (3) and mowing
blade (1).
Installing
● Clean the blade contact surface and
blade bushing (4).
● Secure the blade fastening screw (2)
with Loctite 243.
● Place the mowing blade (1) on the
blade bushing (4) as shown.
● Position the retaining washer (3) as
shown and tighten with the blade
fastening screw (2) to 60 - 65 Nm.
12.4)
12.2).
12.5 Engine
Maintenance interval:
14
See engine instruction manual.
General information:
Observe the operating and maintenance
instructions contained in the attached
engine instruction manual.
To achieve a long service life, it is always
12.2).
particularly important to maintain a
sufficient level of oil and to change the oil
and air filter regularly.
The recommended oil change intervals as
well as information on engine oil and oil
capacities can also be found in the engine
instruction manual.
Risk of injury!
The prescribed tightening torque
for the blade fastening screw must
be observed.
The retaining washer (3) must be
replaced each time the blade is
installed.
The blade fastening screw (2) must
be renewed each time the blade is
replaced.
0478 111 9936 B - EN

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Rm 2 rcRm 2 rt

Table des Matières