Working With Your Machine - Stihl RM 2 R Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 49
Observe the local regulations regarding
permitted operating times for gardening
power tools with combustion engines or
electric motors.
Carefully inspect the complete area on
which the machine is to be used and
remove any stones, sticks, wires, bones
and other foreign objects which could be
thrown up by the machine. Obstacles (e.g.
tree stumps, roots) can be easily
overlooked in long grass.
For this reason, mark all foreign objects
(obstacles) which are hidden in the lawn
and cannot be removed before
commencing work with the machine.
All faulty, worn or damaged parts must be
replaced before using the machine.
Replace any illegible or damaged danger
signs and warnings on the machine. Your
STIHL specialist has a supply of
replacement stickers and all the other
spare parts.
Check secure seating of the spark plug
socket on the spark plug before using the
machine.
The machine must only be used in good
operating condition. Before each use,
check whether:
– The machine is properly assembled.
– The cutting tool and the entire cutting
unit (mowing blade, fastening elements,
mowing deck housing) are in good
condition. In particular check for secure
fastening, damage (notches or cracks)
and wear. (
12.2)
– The tank cap is properly attached.
– The tank and fuel-carrying parts as well
as the tank cap are in good condition.
0478 111 9936 B - EN
– The safety devices (e.g. motorstop
lever, housing, handlebar, protective
grille) are in good condition and working
properly.
– The oil cap is properly attached.
Carry out any necessary work or consult a
specialist dealer. STIHL recommends
STIHL specialist dealers.

4.6 Working with your machine

Never work when animals or
persons, particularly children,
are in the danger area.
The switch and safety devices installed in
the machine must not be removed or
bypassed. In particular, never secure the
motorstop lever to the handlebar (e.g. by
tying it).
Caution – risk of injury!
Never put hands or feet on or
underneath rotating parts.
Never touch the rotating blade.
Always observe the safety distance
provided by the handlebar. The handlebar
must always be installed correctly and
must not be modified. Never operate the
machine with the handlebar folded down.
Never attach any objects to the handlebar
(e.g. work clothing).
Only work during the day or with good
artificial light.
Do not operate the machine in the rain or
during thunder storms, particularly when
there is a risk of lightning strike.
The risk of accidents is higher if the ground
is damp due to increased danger of
slipping.
Particular caution should be exercised
during working in order to prevent slipping.
If possible, avoid using the machine when
the ground is damp.
Exhaust gases:
Danger to life through poisoning!
In the case of nausea, headache,
impaired vision (e.g. decreasing
field of view) hearing disorder,
dizziness, decreasing power of
concentration, stop working
immediately. These symptoms may
be caused by excessively high
exhaust gas concentrations.
The machine generates
poisonous exhaust gases when
the engine is running. The
gases contain poisonous
carbon monoxide, a colourless and
odourless gas, as well as other pollutants.
The engine must never be operated in
closed or poorly ventilated spaces.
Starting:
Exercise care when starting the machine
and observe the instructions contained in
the section entitled "Operating the
machine" (
11.). Starting the machine in
accordance with these instructions
reduces the risk of injury.
Risk of injury!
If the starter rope recoils at speed, the
hand and arm will be pulled towards the
engine faster than the starter rope can be
released. This kickback can result in
broken bones, crush injuries and sprains.
Keep your feet a safe distance from the
cutting tool when starting the machine.
The machine must not be tilted during
start-up.
The self-propulsion lever must not be
pressed when starting the engine.
33

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Rm 2 rcRm 2 rt

Table des Matières