Evolution F255 SMS Instructions D'origine page 7

www.evolutionpowertools.com
increased risk of injury from blade contact.
c) The workpiece must be stationary and
clamped or held against both the fence
and the table. Do not feed the workpiece
into the blade or cut "freehand" in any way.
Unrestrained or moving workpieces could be
thrown at high speeds, causing injury.
d) Push the saw through the workpiece.
Do not pull the saw through the workpiece.
To make a cut, raise the saw head and pull
it out over the workpiece without cutting,
start the motor, press the saw head down and
push the saw through the workpiece. Cutting
on the pull stroke is likely to cause the saw
blade to climb on top of the workpiece and
violently throw the blade assembly towards
the operator.
NOTE: The above warning is omitted for a
simple pivoting arm mitre saw.
e) Never cross your hand over the intended
line of cutting either in front or behind the
saw blade. Supporting the workpiece "cross
handed" i.e. holding the workpiece to the right of
the saw blade with your left hand or vice versa is
very dangerous.
f) Do not reach behind the fence with either
hand closer than 150mm from either side of
the saw blade, to remove wood scraps, or for
any other reason while the blade is spinning.
The proximity of the spinning saw blade to
your hand may not be obvious and you may be
seriously injured.
g) Inspect your workpiece before cutting. If
the workpiece is bowed or warped, clamp it
with the outside bowed face toward the fence.
Always make certain that there is no gap
between the workpiece, fence and table along
the line of the cut. Bent or warped workpieces
can twist or shift and may cause binding on the
spinning saw blade while cutting. There should
be no nails or foreign objects in the workpiece.
h) Do not use the saw until the table is clear
of all tools, wood scraps, etc., except for
the workpiece. Small debris or loose pieces
of wood or other objects that contact the
revolving blade can be thrown with
high speed.
i) Cut only one workpiece at a time. Stacked
multiple workpieces cannot be adequately
clamped or braced and may bind on the blade
or shift during cutting.
j) Ensure the mitre saw is mounted or placed
on a level, firm work surface before use. A
level and firm work surface reduces the risk of
the mitre saw becoming unstable.
k) Plan your work. Every time you change
the bevel or mitre angle setting, make
sure the adjustable fence is set correctly to
support the workpiece and will not interfere
with the blade or the guarding system.
Without turning the tool "ON" and with no
workpiece on the table, move the saw blade
through a complete simulated cut to assure
there will be no interference or danger of
cutting the fence.
NOTE: The phrase "bevel or" does not apply for
saws without bevel adjustment.
l) Provide adequate support such as table
extensions, saw horses, etc. for a workpiece that
is wider or longer than the table top. Workpieces
longer or wider than the mitre saw table can tip
if not securely supported. If the cut-off piece or
workpiece tips, it can lift the lower guard or be
thrown by the spinning blade.
m) Do not use another person as a
substitute for a table extension or as
additional support. Unstable support for
the workpiece can cause the blade to bind
or the workpiece to shift during the cutting
operation pulling you and the helper into the
spinning blade.
n) The cut-off piece must not be jammed or
pressed by any means against the spinning
saw blade. If confined, i.e. using length stops, the
cut-off piece could get wedged against the blade
and thrown violently.
o) Always use a clamp or a fixture designed
to properly support round material such as
rods or tubing. Rods have a tendency to roll
while being cut, causing the blade to "bite" and
pull the work with your hand into the blade.
p) Let the blade reach full speed before
contacting the workpiece. This will reduce
the risk of the workpiece being thrown.
q) If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece
could cause loss of control or damage to the
mitre saw.
r) After finishing the cut, release the switch,
hold the saw head down and wait for the
blade to stop before removing the cut-off
piece. Reaching with your hand near the
coasting blade is dangerous.
s) Hold the handle firmly when making an
7
EN