Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
WARNING: Never pull the cutting head and
spinning blade towards you when making a
sliding cut. The blade may try to climb up on
top of the work-piece, causing the cutting
head to 'kickback' forcefully.
The cutting head should always be
positioned as outlined above before
attempting to make a sliding cut. When
the cutting head is in the correct position
above the work-piece it can be lowered
and pushed rearwards towards the fence to
complete the cut.
MITRE CUTTING (Fig. 58)
The rotary table of this machine can be turned
through 50˚ to the left or right from the normal
cross-cut (0˚) position.
Positive stops are provided at 45˚, 30˚, 22.5˚
and 15˚ to both the right hand and left hand
sides.
Mitre Cutting is possible with or without the
sliding carriage system being deployed.
• Loosen the mitre handle locking knob
(Fig. 56) by turning the locking knob anti-
clockwise.
• Pull up the positive stop locking lever.
(Fig. 57)
• Turn the rotary table to the desired angle.
Note: A protractor scale is incorporated into
the machines base to aid setting.
• Tighten the mitre handle locking knob when
the angle is achieved.
Note: It is good practice to tighten the Mitre
Locking Knob even when a positive stop is
selected and the Positive Stop Locking Lever is
positively engaged.
BEVEL CUTTING BY
TILTING THE CUTTING HEAD
A bevel cut (Fig. 55) is made with the rotary
table set at 0˚ mitre angle.
Note: It may be necessary to adjust the
upper section of the sliding fence to provide
clearance for the moving cutting head. (Fig.
29-30)
The cutting head can be tilted from the normal
0˚ (perpendicular position) to a maximum
angle of 45˚ from the perpendicular to the left
hand side only. Bevel cutting is possible with
or without the sliding carriage system being
deployed.
www.evolutionpowertools.com
Note: A positive stop is provided at 33.9˚
Bevel angle. This is accessed by deploying
(pushing inwards) the 33.9˚ Bevel Pin. (Fig. 59)
Normally the Bevel Pin should be left in the
un-deployed (pulled out) position.
To tilt the cutting head to the left:
• Loosen the bevel lock handle. (Fig. 60)
• Tilt the cutting head to the required angle.
A protractor scale is provided as an aid to
setting. (Fig 61)
• Tighten the bevel lock handle when the
desired angle has been selected.
• Stand to the left side of the Cutting Handle
when making a cut.
When cutting is completed:
• Release the ON/OFF trigger switch to switch
off the motor, but keep your hands in
position.
• Allow the blade to come to a complete stop.
• Allow the cutting head has to rise to its
upper position, with the lower blade guard
completely deployed and covering the
blade before removing yours hand(s).
• Return the cutting head to the
perpendicular position.
COMPOUND CUTTING (Fig. 62)
A compound cut is a combination of a mitre
and bevel cut employed simultaneously.
When a compound cut is required, select the
desired bevel and mitre positions as
previously described.
Note: Compound Cutting with the sliding
carriage system deployed is possible.
Always check that the sliding blade does not
interfere with the machines fence or any other
parts of the machine. Adjust the upper left
hand section of the sliding fence if necessary.
CROWN MOULDING CUTTING
This machine is capable of cutting the
mitre angles required for Crown Mouldings.
To configure the machine to cut Crown
Moulding:
• Deploy the 33.9˚ Bevel Pin by pushing it fully
inwards. (Fig. 59)
• Tilt the cutting head to the 33.9˚ position
and lock it in place by tightening the bevel
lock handle.
• Turn the rotary table and set it to 31.6˚ mitre
angle as indicated by the protractor scale.
Ensure that the Crown Moulding is correctly
positioned on the rotary table and secure it
with appropriate clamps before making the cut.
28
Publicité
Table des Matières
