Remote Control Features - Danby DPAC8020 Manuel D'utilisation

Remote Control Features

(DPAC8020 ONLY)
The hand held remote unit allows you to control all
operational aspects (excluding Auto-Timed
Programs) of your Portable 4 Season Home Comfort
Appliance from the convenience of your favorite
armchair. Here are some things you should know
about operating the unit with the hand held remote.
Upper Control Buttons
I/O: Power switch (On/Off).
Mode: Selects the operating mode
(Auto–Cool–Dry/Dehumidifier–Heat–Fan).
The "auto" mode is a built in feature activated from
the hand held remote unit only. Under "auto" mode,
your unit will automatically select the required
operating mode based on temperature selection.
Dehumidifying mode is not operational under the
"auto" mode function.The main unit will respond
automatically, switching appropriately between
modes "cool-heat-fan" to maintain the selected
temperature.
Fan: Selects fan speed settings (Auto–LOW-MED-HIGH).
NOTE: The "Auto" fan speed setting is
equivalent to "Medium" fan speed.
Used to adjust (increase) both time of day
clock settings and temperature settings.
(1 min. increments) for time of day clock settings.
(1° increments) on the Celsius scale.
(2° increments) on the Fahrenheit scale.
TEMP/TIMER
Used to adjust (decrease) both time of day
clock settings and temperature settings.
(1 min. increments) for time of day clock settings.
(1° increments) on the Celsius scale.
(2° increments) on the Farenheight scale.
Lower Control Buttons
(Under Lower Sliding Cover)
Swing: Used to activate automatic air swing
(oscillating) feature (70° swing).
Set: Used to lock/register time of day setting.
Clock: Used to initiate time of day clock setting.
L: (Lock) Used to lock a selected program mode
(Against accidental program change).
R: (Re-set) Used to cancel/reset locked programs.
(Clock setting will also be erased)
˚C/˚F: Used to select temperature settings in either
"Celsius" or "Farenheight".
To operate the remote, you will require two "AAA"
Alkaline batteries (included).
Batteries should be replaced when:
a) No signal (beep) is heard while attempting to
program the main unit.
b) No symbol " " appears in the remote LCD
window when a command is initiated.
Battery replacement:
1. Slide the lower control cover on the remote down
until it stops. Continue pulling (gently) until the
lower section separates completely from the unit.
2. Insert batteries (AAA) as depicted inside the
battery chamber.(+/-)
3. Re-install lower cover.
4. If the remote control is not being used for
extended periods of time (vacations etc.),
batteries should be removed.
The remote operates within a range of 7 meters
(23 ft.) from the receiver located inside the main unit.
Any obstruction between the receiver and remote
may cause signal interference, limiting the ability to
program the main unit.
NOTE: The illuminated control panel feature on
the main unit is not operational when setting
functions using the remote control unit. (this is
normal)
Instrucciones para la instalación
del tanque de agua (continúa)
3. Ponga el tanque de agua a la posición correcta sobre la reborde
apoyante. Asegúrese de que el conector rápido sobre el tanque de
agua está alineado con el conector rápido, instalado a la factoría,
localizado al posterior del armario. (véase la figura 37)
Fig.37
4. Para hacer la coneción, empuje el conector del tanque de agua en
el conector del armario. Ud. va a oír un chasquido positivo cuando
hace la coneción
5. Instale la tapa sobre el tanque de agua.
6. Para desenganchar (desconectar) el tanque de agua externo,
apreta el botón de desenganchar que está en la parte superior del
conector rápido del armario, pues sujete los mangos de
desenganchar localizado por ambos lados del tanque,
levante y tire hacia adelante. (véase la figura 38, 39)
Fig.38
Fig.39
PRECAUCIÓN
Es necesario vaciar el agua acumulada en ambos tanques
antes de mover la unidad.