Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
pull the starter rope (5) briskly until the engine starts or turn
and hold the electric starter key towards "Start" until the engine
starts (PL6950/8950 only)
b.
To start the electric motor, move the ON/OFF switch to the ON
position.
7. Turn the pressure control knob (1) clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent flows freely from the bleed hose.
8. Turn off the sprayer.
a.
To turn off the gas engine,
•
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
•
move the throttle lever to the slow position, and
•
turn the engine switch to the OFF position.
b.
To turn off the electric motor,
•
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
•
move the ON/OFF switch to the OFF position.
9. Remove the bleed hose from the waste container and place it
into the container of paint.
10. Close the bleed valve by turning it fully clockwise.
11. Start the engine or turn on the electric motor.
12. Turn the pressure control knob clockwise approximately 1/3
of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Earth the gun by holding it against the edge of the
metal container while flushing. Failure to do so may
lead to a static electric discharge, which may cause
a fire.
14. Trigger the gun into the metal waste container until all air and
solvent is flushed from the spray hose and paint is flowing
freely from the gun.
15. Lock the gun by turning the gun trigger lock to the locked
position (fig 10).
16. Turn off the sprayer.
17. Attach tip guard and tip to the gun as instructed by the tip
guard or tip manuals.
POSSIBLE INjECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the unclog
position. Always engage the gun trigger lock before
removing, replacing or cleaning tip.
18. Start the engine or turn on the electric motor.
19. Increase the pressure by turning the pressure control knob
slowly clockwise and test the spray pattern on a piece of
cardboard. Adjust the pressure control knob until the spray
from the gun is completely atomized.
i
Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear and
additional overspray.
PowrLiner
GB
4.5
Pressure Relief Procedure
Be sure to follow the Pressure Relief Procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray nozzles, or preparing for
cleanup.
1. Lock the spray gun by turning the gun trigger lock to the
locked position.
2. Turn off the sprayer.
a.
To turn off the gas engine,
•
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
•
move the throttle lever to the slow position, and
•
turn the engine switch to the OFF position.
b.
To turn off the electric motor,
•
set the pressure to minimum by turning the pressure control
knob fully counterclockwise,
•
move the ON/OFF switch to the OFF position.
3. Close the hydraulic shut-off valve on the hydraulic pressure
hose.
4. Unlock the gun by turning the gun trigger lock to the
unlocked position.
5. Hold the metal part of the gun firmly to the side of a metal
waste container to earth the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any pressure that may still be in the
hose.
7. Lock the gun by turning the gun trigger lock to the locked
position.
8. Place the bleed hose into the metal waste container.
9. Open the bleed valve by turning it fully counterclockwise.
4.6
Operating the Front Caster
The front caster on the cart is designed to track the sprayer in either
a straight line or allow free motion. Standing behind the sprayer, the
trigger on the left handle of the cart controls the operation of the
front caster.
1. To lock the front caster in the straight line position, squeeze
then release the caster trigger and move the sprayer forward.
2. To allow free motion of the front caster, squeeze and hold the
caster trigger.
11
Operation
Publicité
Chapitres
Table des Matières
