Publicité
Les langues disponibles
Les langues disponibles
WHAT TO DO IF...
(guide to problem resolution)
The motor does not move even though the power supply is pre-
sent:
– check whether the thermal protection has been activated: in this case,
it is sufficient to wait until the motor cools;
– check the presence of the mains voltage and the correspondence be-
tween the measured values and the engine plate data, by measuring
between Common and the electrical phase supplied; to finish, try sup-
plying the opposite electric phase;
– check whether the two limit switches, due to incorrect adjustment, ac-
tivate at the same time; in this case, turn the two adjustment screws a
few turns in a clockwise direction (+).
If, at the end of these checks, the motor persists in not moving, there is
probably a serious failure.
PRODUCT DISPOSAL
This product is an integral part of the automation system and must
therefore be scrapped with the rest of the latter.
As for installation, at the end of the life of this product, the dismantling
operations must be carried out by qualified personnel.
This product is made from various materials: some may be recycled, oth-
ers must be scrapped. Research the recycling or disposal systems pro-
vided by the standards in force in your country for this product category.
CAUTION! - Some components of the product may contain
polluting or hazardous substances which could, if disposed of in
nature, have harmful effects on the environment and on people's
health.
As indicated by the symbol shown, it is forbidden to discard
this product in household refuse collection facilities. Sort the
components, to ensure their elimination in accordance with lo-
cal standards in force, or return the product to the seller when
purchasing a new equivalent product.
CAUTION! – The local regulations in force may impose heavy
penalties in the event of illegal disposal of this product.
TECHNICAL CHARACTERISTICS
WARNINGS: • All technical characteristics shown refer to an ambient
temperature of 20°C (± 5°C) • Nice S.p.a. reserves the right to make
changes to the product when it deems this necessary, whilst guaran-
teeing the same functions and usage for which the product is intended.
• Power supply voltage and frequency; Current and power;
Torque and speed: See technical data on the label on the motor
• Motor body diameter: 45 mm
• Continuous operation nominal duration:
maximum 4 minutes
• Degree of protection: IP 44
• Minimum operating temperature: -20°C
EC DECLARATION OF CONFORMITY
Declaration in accordance with Directives:
2014/35/EU (LVD) and 2014/30/EU (EMC)
RM1517, RM3017, RM5012 are products of NICE S.p.a. (TV) I
The content of this declaration corresponds to that specified in the
official document deposited at the Nice S.p.a. headquarters and,
in particular, to the latest revised edition available prior to the pub-
lishing of this manual. The text herein has been re-edited for edito-
rial purposes. A copy of the original declaration can be requested
from Nice S.p.a. (TV) I.
Declaration number: 578/RM
Revision: 0
Language: EN
• Manufacturer's name: NICE S.p.A.
• Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) It-
aly
• Type of product: Tubular motor for roller shutters and awnings
• Model / Type: RM 1517, RM 3017, RM 5012
• Accessories: none.
The undersigned Roberto Griffa, as Chief Executive Officer, here-
by declares under his own responsibility that the product identified
above complies with the provisions of the following directives:
• DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT AND
COUNCIL of 26 February 2014 on the approximation of the laws
of Member States relating to the making available on the market
of electrical equipment designed for use within certain voltage lim-
its (recast), according to the following harmonised standards: EN
60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006
+ A13:2008 + A14:2010 + A15:2011 ; EN 60335-2-97:2006 +
A11:2008 + A12:2015 + A2:2010 ; EN 62233:2008
• DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT
AND COUNCIL of 26 February 2014 on the approximation of
the laws of Member States relating to electromagnetic compat-
ibility (recast), according to the following harmonised standards:
EN 55014-1:2006 + A1:2009 + A2:2011 ; EN 55014-2:1997 +
A1:2001 + A2:2008 ; EN 61000-3-2:2014 ; EN 61000-3-3:2013
Oderzo, 28 July 2016
Ing. Roberto Griffa
(Chief Executive Officer)
English – 10
Publicité
