Only use original Webasto spare parts.
Go to the Webasto online shop for part numbers.
www.webasto-charging.com
Switch off and secure the power supply to the charging
X
X
station.
Remove cover of the connection terminals (Fig. 03).
X
X
Disconnect the electrical supply cable.
X
X
Remove the screws and washers at the bottom.
X
X
Detach the charging station from the mounting frame.
X
X
Remove cable clamp from the charging cable (Fig. 13; 1).
X
X
Disconnect PE conductor (Fig. 12: PE).
X
X
Turn the charging station to open the maintenance flap
X
X
on the back. (Fig. 13, 6). The cover is sealed.
Disconnect the remaining wires of the charging cable
X
X
(Fig. 13; 1-5).
Replace the charging cable.
X
X
Reassemble and mount the charging station in reverse
X
X
order. To maintain the IP 54 protection class, make sure
that the O-ring is fitted correctly.
Switch on the power supply to the charging station.
X
X
Make sure that the charging station successfully
X
X
completes the self-test to ensure its functionality.
12 Disposal
The symbol of the crossed-out waste bin indicates
that this electrical/electronic device must not be
disposed of in household waste at the end of its
service life. Dispose of the device free of charge
at a local collection point for electrical/electronic
devices. Addressed can be obtained from your city or
local authority. Separate collection of electrical and
electronic devices enables re-use, material recycling
or other forms of re-utilisation of waste equipment
while also avoiding the negative effects of hazardous
substances which may be contained in the devices on
the environment and for human health.
WEEE Reg No: DE 17725267
Dispose of packaging in corresponding recycling
X
X
container in accordance with national regulations.
Webasto PURE
13 Annex
13.1 Technical data
Data
Rated voltage
230 VAC / 400 VAC
Rated current
16 or 32 A AC
Supply frequency
50 Hz
Overvoltage category III as per EN 60664
Protection class
I
IP-protection class
IP 54 (the IP code denotes the
scope of protection a housing
offers in terms of contact and for-
eign objects as well as moisture/
water in accordance with DIN EN
60529 (VDE 0470-1)).
Mechanical protection
IK 10 (the IK code denotes the
class
protection class offered by a en-
closure to damaging mechanical
load)
Residual direct current
RDC-MD universal current sensitive
monitoring device
DC fault current protection 6 mA
to protect the RCD IN = 30 mA
Type A installed in the household
system.
Connection cross
Depending on the cable and
section
type of installation, the minimum
cable cross-section for a standard
installation is:
– 6 mm² (for 16 A)
– 10 mm² (for 32 A).
Connection tech-
IEC 62196-2
nology
Mains connection
Connection cable:
■
■
terminal
Rigid (min.-max.) 2.5-6 mm²
■
■
Flexible (min.-max.) 2.5-
16 mm²
■
■
AWG (min.-max.) 13-6
■
■
Flexible (min.-max.) with cable
end ferrule without/with plastic
sleeve: 2.5-10/2.5-10 mm²
Output voltage
230 VAC / 400 VAC
Data
Max. charging power 3.7-22 kW adjustable
Operating tempera-
-25 to +55°C
ture range
Storage temperature
-25 to +80°C
Indicator
LED + buzzer
Lock
Key-operated switch to enable
charging
Altitude
Max. 3000 m above sea level
Permissible relative
5 to 95% no condensation
humidity
Cooling system
Passive
Weight
5.56 kg
Dimensions [mm]
See Fig. 10
13.2 Declaration of Conformity with the product
standards
The Webasto PURE was developed, manufactured, tested
and supplied in accordance with the relevant directives,
regulations and standards for safety, EMC and environmen-
tal compatibility.
Webasto declares that the product Webasto PURE is ma-
nufactured and delivered in accordance with the following
directives and regulations:
– 2014 /35/EU Low Voltage Directive
– 2014/30/EU EMC Directive
– 2011/65/EU RoHS Directive
– 2001/95/EG Product Safety Directive
– 2012/19/EU Waste Electrical and Electronic Equipment
Directive
– 1907/2006 REACH regulation
The complete CE Declaration of Conformity can be found in
the download area under https://webasto-charging.com/.
See Fig. 02 QR code for documentation.
7