Güde GTK 721 Traduction Du Mode D'emploi D'origine page 10

Introduction
To enjoy your new table circular saw as long as possible,
please read carefully the Operating Instructions and the
attached safety instructions before using it. Further, we
recommend keeping the Operating Instructions to recall the
product features in the future.
Within the continuous product development, we reserve
the right to make technical changes to improve it.
This document represents translation of the original
Operating Instructions.
Machine description (pic. 1)
1 Circular-saw blade
2 Miter cutting stop
3 Saw table
4 Star screw to adjust the parallel guide
5 Circular-saw blade angle adjustment
6 On/Off
7 Adjusting lever
8 Stand
9 Engine
10 Parallel stop
11 Circular-saw blade cover
12 Sawdust box cover
16 Sliding bar
22 Side cover
23 Foot
Use as designated
The table circular saw is used for longitudinal and cross
cutting (with angle stop only) of wood of all types, depending
on the machine size.
This machine must not be used for any works other than for
which the machine has been designed and that are specified
in the Operating Instructions.
Any other use will be considered a use in conflict with the
designation. The manufacturer will not be liable for any
consequential damage or injuries. Please be sure to know
that the machine has not been designed for industrial
purposes.
Use in conflict with designation
Any use of the machine not specified in the "Use as
designated" section are considered a use in conflict with the
designation.
The table circular saw cannot be used for the following
purposes:
•
It cannot be used for cutting logs of all types.
• Circular-saw blades suitable for this machine to be used
only. Using dividing wheels of all types prohibited.
There is a risk of injury.
The machine user will be liable for any material and personal
damage that has been caused as a result of inappropriate use
of the machine.
Original spare parts or components approved by the
manufacturer to be used only.
Supply includes
Take the machine out of the transport package and check it
whether there are the following parts:
1 piece GTK 721 table circular saw
1 piece Sliding bar
1 piece Angle stop
3 pcs Parallel stop
1 piece Sintered carbide circular-saw blade
1 piece User Guide
Please contact your dealer if any parts are missing or are
damaged.
Technical specifications:
Voltage:
Output:
Min. protection:
Idle speed:
Sintered carbide
Circular-saw blade:
Teeth:
Table size:
Table height:
Max. cutting height:
Insulation class:
Protection type:
Level of sound
Pressure dB (A):
Guaranteed level of acoustic
performance dB (A):
Weight:
The measured values have been found according to IEC
60335-2-100 and EN 60335-2-100.
General safety instructions
The Operating Instructions must be read thoroughly before
using the machine for the first time. If there are any doubts
regarding the machine connection and operation, please
contact the manufacturer (service department).
PLEASE FOLLOW CAREFULLY THESE INSTRUCTIONS
TO ENSURE A HIGH SAFETY LEVEL:
Caution: To be used with RCD 30 mA (safety
switch against stray current) only!
CAUTION!
•
Keep the place of your work clean and tidy. Mess in
the place of your work and on the work table increases
the risk of accidents and injuries.
•
Pay attention to conditions of the environment where
you are working. Do not use electric tools and machine
tools in a moist and wet environment. Provide adequate
lighting. Do not expose electric tools to rain or high air
humidity. Do not switch electric tools on near highly
flammable liquids and gases.
•
Do not let other persons to the machine. Keep visitors
and bystanders, especially children and ill or weak
persons, in safe distance from the place of your work.
•
Make sure your machine is stored safely. Keep
machines that are not being used in a dry place,
elevated if possible and lock them to make them
inaccessible to other persons.
• At all times, use the right machine for each work. Do
not use e.g. small machines or accessory equipment for
works that actually need to be performed by big
machines. Use your machines solely for purposes for
which they have been designed. Keep your machine
clean and sharp at all times.
• Provide adequate clothing. Do not wear any loose
clothing and jewels. They could get caught by the
10
230 V~50 Hz
720 W
16 A inertial
-1
2,950 per min
205 mm
20
500 x 400 mm
240 mm
90° 43 mm / 45° 25 mm
B
IP 44
95 db (A) K = 3 dB (A)
108 dB (A)
12.5 kg