Publicité
ES/EM 98 Extreme
//
Montage- und Anschlussanleitung / Positionsschalter
Mounting and wiring instructions / Position switch
Instructions de montage et de câblage / Interrupteur de position
Istruzioni di montaggio e collegamento / Interruttore di posizione
Instruções de montagem e instalação / Chave fim de curso
Инструкция по монтажу и подключению / Позиционный выключатель
Deutsch (Originalbetriebsanleitung)
liegt im Verantwortungsbereich des Herstellers einer Anlage oder Ma-
schine, die korrekte Gesamtfunktion sicherzustellen. Technische
Änderungen vorbehalten.
Instandhaltung, Wartung und Reparatur
=
GEFAHR
Spannungsführende Teile. Stromschlaggefahr!
Beschädigte und defekte Geräte nicht reparieren,
sondern ersetzen. Ausnahme: Reparatur nur mit
Original-Ersatzteilen von steute durchführen. Um-
bauten und Veränderungen am Gerät unterlassen.
Bei rauen Betriebsbedingungen empfehlen wir eine regelmäßige
Wartung mit folgenden Schritten:
1. Betätiger auf Leichtgängigkeit prüfen.
2. Entfernen von Schmutzresten.
3. Prüfen der Leitungseinführung und -anschlüsse.
Reinigung
=
GEFAHR
Spannungsführende Teile. Stromschlaggefahr!
Schutzart beachten.
- Bei feuchter Reinigung: Wasser oder milde, nicht-scheuernde,
nicht-kratzende Reinigungsmittel verwenden.
- Keine aggressiven Reinigungs- oder Lösungsmittel verwenden.
Entsorgung
- Nationale, lokale und gesetzliche Bestimmungen zur Entsorgung
beachten.
- Materialien getrennt dem Recycling zuführen.
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer.
In case of doubt, the German language version of these instructions
shall prevail.
Scope of delivery
1 device, 1 mounting and wiring instructions, carton.
Safety information
=
In this document, the warning triangle is used
together with a signal word to indicate a
hazardous situation.
The signal words have the following meanings:
NOTICE
indicates a situation which may
result in material damage.
WARNING
indicates a situation which may
result in serious injury or death.
Intended use
The position switch ES/EM 98 with safety function is used in safety cir-
cuits to monitor the position of mobile safety guards to EN ISO 14119
(EN 1088) type 1 and EN 60947-5-1.
Installation, mounting and dismantling
=
DANGER
Live parts. Electric shock hazard! Connecting and
disconnecting only to be performed by qualified and
authorised personnel. Connecting and disconnect-
ing only in zero potential state.
=
DANGER
Untight if mounted at low temperatures. Electric
shock hazard! Mount carefully at low temperatures.
NOTICE
Incorrect installation causes leakage. Danger of
malfunction. Only operate with an actuator. Use fit-
ting cable gland only. Observe tightening torque of
cover and actuator.
Mount the device on an even surface. Ensure that the device cannot be
moved from its position. Ensure this in case of failure, too. For protec-
tion against unauthorized manipulation, use e.g. one way safety
screws. These are optionally available. When mounting the device, ob-
serve the requirements of EN 14119, especially the sections 5.1 to
5.4! Observe the instructions in the standards EN ISO 12100 and
EN ISO 14120.
2 / 16
CAUTION
indicates a situation which may
result in minor or moderate
injury.
DANGER
indicates a situation which will
result in serious injury or death.
Publicité
