Assembly; Design Features Abb./Fig. A; Electrical Connection - Scheppach Biostar 3000 Traduction Du Manuel D'origine

• Do not set up any provisional electrical connec-
tions.
• Never bypass protective devices or deactivate
them.
• Only hook up the machine by means of a fault-
current circuit breaker (30 mA).
• The electrical connection or repairs to electrical
parts of the machine must be carried out by a cer-
tified electrician or one of our customer service
points. Local regulations – especially regarding
protective measures – must be observed.
• Damaged mains leads must be replaced by the ma-
nufacturer or one of their service workshops or a
similar qualified person to prevent dangers.
• Repairs to other parts of the machine must be car-
ried out by the manufacturer or one of his customer
service points.
• Use only original spare. Accidents can arise for
the user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.

Assembly

Your garden shredder is not fully assembled due to
technical packing difficulties.
Assembly tools
Included in the items delivered are:
1 Hexagon socket head wrench 4 mm
Design features, Abb. / Fig. A
Filling chute, flap, funnel Abb. / Fig. ,,A"
1 Filling chute
2 Safety screw
3 Flap
4 Funnel
• Fit filling chute (1) with the housing open
Front side, bottom
2 flat, round screws
2 serrated washers
2 2 safety cap nuts
Rear side, bottom
2 flat, round screws
2 serrated washers
2 safety cap nuts
• Close the housing and screw safety screws (2)
all the way in.
• Insert flap (3) into the filling chute, fit the funnel
(4) and fasten in place.
Rear side, funnel
2 flat, round screws
2 serrated washers
2 safety cap nuts
Front side, funnel
2 flat, round screws
2 serrated washers
2 safety cap nuts
Insulating mat, chute trim Abb. / Fig. „B"
1 insulating mat
2 chute trim
3 cover
Insert the insulating mat (1) into the funnel chute from
below.
In doing so, the noise absorbing side (textured) must
lie on the noise opening of the filling chute.
As an alternative, some devices are equipped with
smooth insulating mats with no texture.
Likewise, insert the chute trim (2) into the funnel chute
from below and screw on.
Screw on the cover (3)
Your garden shredder is now fully assembled
The installed electric brake motor is ready to be put
into operation.
The connection meets the relevant VDE and DIN re-
quirements.
The electric brake motor causes the disc blade to
come to a near immediate standstill after the machine
has been turned off.
Firring, repair and maintenance work on the electric
unit can only be carried out by a qualified electrician.
Important notes
Damaged electrical connection cables
M6x16 Insulation damage often occurs with electrical con-
Ø 6 nection cables.
M6 Some causes are:
• Pressure points, especially when electrical connec-
M6x16 • Kinks caused by improper handling or mowing of
Ø 6
M6 • Cuts resulting from being run over
• Insulation damages caused by pulling the cable out
• Cracks resulting from aging of the insulation.
Such insulation damaged electrical connection cables
cannot be used and are, as a result of their insulation
damage. LIFETHREATENING!!
Check the electrical cable connections on a regular
basis. When checking the cables, make sure that the
M6x20 cables are not stuck to the electrical network.
Ø 6 Electrical cable connections built with seal contacts
M6 must meet the relevant VDE and DIN requirements.
Only use electrical cable connections with a rating of
at least H 07 RN or a rubber sheathed cable.
M6x16 The type rating of the connection cable must be prin-
Ø 6 ted on the cable.
M6
2 self-tapping screws
2 washers
1 lenticular flange head screw
1 serrated washer
m Electrical connection
tion cables are run through window or door cracks.
the electrical connection cables.
of wall sockets.
Ø 4,2 x 16
Ø 5
M6 x 20
Ø 6
English 17