Publicité
Les langues disponibles
Les langues disponibles
Safety
safety information
Carefully read and follow all safety
instructions in this manual or on pump.
this is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential for
personal injury!
warns about hazards that will cause serious
personal injury, death or major property damage if ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The word notiCe indicates special instructions which are
important but not related to hazards.
1. read these rules and instructions carefully. Failure to
follow them could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must
comply with their rules.
Hazardous voltage. Can shock, burn or kill.
During operation the pump is in water. to avoid fatal
shocks, proceed as follows if pump needs servicing:
3A. Disconnect power to outlet box before unplugging
pump.
3B. Unplug the pump before handling or servicing it.
3C. Take extreme care when changing fuses. Do not stand
in water or put your finger in the fuse socket.
3D. Do not modify the cord and plug. When using the
cord and plug, plug into a grounded outlet only. When
wiring to a system control, connect the pump ground
lead to the system ground.
4. Do not run the pump dry. Dry running can overheat
the pump (causing burns to anyone handling it), and
will void the warranty.
5. The pump normally runs hot. To avoid burns when
servicing pump, allow it to cool for 20 minutes after
shutdown before handling it.
6. The pump is permanently lubricated. No oiling or
greasing is required in normal operation.
PumP, motor, sWitCH & CorD sPeCifiCations
motor
motor full
HP
Load amps
.30
8.0
individual
Branch Circuit
Cord Length
required (amps)
in ft. (m)
15
10 (3)
7. Do not install the basin and pump in any location
classified as hazardous by the United States National
Electrical Code (NEC), or by the Canadian Electrical
Code (CEC), where applicable.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
PumP sPeCifiCations
Power Supply Required ............................ 115V, 60 Hz
Individual Branch Circuit Required ..................15 Amps
Maximum Liquid Temperature .................. 120°F (50°C)
Discharge Adapter ...................................... 1-1/2
DesCriPtion
The Hydromatic Sump Pump System, Model Number
CSS-3D or CSS-3V, is ideal for basement and cellar
installations. It includes a submersible sump pump and
a corrosion-resistant sump basin and lid. The pump
features a flush-mount system for maximum discharge of
the basin. All components of the sump pump system are
preassembled at the factory for easy installation.
This submersible pump is designed for sump drainage,
dewatering and flood control. The pump has built-in
thermal overload protection and an automatic reset. The
mechanical seal and ball bearings on the motor shaft are
permanently lubricated.
This system is designed for residential use only. The
supplied hardware kit includes a rubber inlet hub, a
cord grommet and an exterior check valve. No special
tools or sealants are required.
notiCe: This system is not designed for applications
involving salt water or brine! Use with salt water or brine
will void warranty.
Pump water only with this pump.
PerformanCe
GPH (LPH) AT TOTAL FEET (METERS)
OF LIFT
model
5 (1.5 m) 10 (3 m) 15 (4.6 m) 20 (6.1 m)
CSS-3D,
2,820
2,280
CSS-3V
(10,675)
(8,631)
*For performance at maximum temperature see Catalog.
switch setting in inches (mm)
on
8 (203)
shown below
1,800
1,020
(7.6 m)
(6,814)
(3,861)
Discharge
adapter
off
size
3-1/2 (89)
1-1/2
"
2
NPT
"
No flow
at height
25 ft
Publicité
