Tool Replacement - stayer SCR315W Instructions D'emploi

Adjustment
1. Carry out steps 1-5 of the checking procedure.
2. Tighten the grip 46 of the telescopic guides 41 to
ensure that it does not move the head when
tightening the adjustment screws.
3. Proceed to adjusting by acting on the two
screws 47 such that the distance between the
keel's inside 39 and the outside of the teeth of
the disk must be at any visible point between 3
mm and 5 mm. Retighten screws 47 and release
grip 46. Assemble the upper area of the machine
in the reverse sense to steps 1-5 of the checking
procedure.

9.Tool Replacement

¡Warning!
Carry out this operation with the machine
unplugged and the disk standing still. Obligatorily
use protective gloves.
Removing the cutting disk
IMAGES B C E
1. Make sure that the machine is in the horizontal
resting position by lowering the head and
locking it by inserting grip 32 into its retainer
hole.
2. Loosen and remove the two fastening screws of
the movable guard 42 and withdraw movable
guard 42.
3. Loosen the 2 butterfly nuts 40 and the 4 screws
53 to remove the upper table 38.
4. Lock the fastening flange 17 for the disk 16 by
means of a flange wrench (a special tool
supplied with the product). Introduce the two tips
of the tool into the two holes of flange 17 and
firmly grasp the flange wrench by its handle to
loosen screw 18 by means of the socket wrench
supplied with the equipment. Attention: it
screws counterclockwise. To loosen it, it must be
turned clockwise.
5. Take out the disk 16 from above in the area that
becomes enabled when removing the upper
cutting disk 38.
Replacing the cutting disk
IMAGES B C E
1. Remove the cutting disk in accordance with the
procedure indicated above.
ENGLISH
42
I
I
42
2. Carefully clean sawdust and debris from the
internal areas.
3. Position the new EN847-conforming cutting disk
such that the direction of the arrow of the
stationary lower guard becomes coincident with
the arrow engraved on the disk and with the
proper inclination of the disk teeth. Introduce the
disk by the area enabled when removing the
upper cutting disk 38 ensuring a perfect contact
with its housing with the motor's drive train.
4. Position flange 17 and the socket screw 18
ensuring a perfect fit of the whole group.
5. Immobilize flange 17 using the flange wrench
supplied with the equipment.
6. Tighten screw 18 counterclockwise using the
socket wrench supplied with the equipment.
7. Assemble the upper cutting table 38 by inserting
it first through the keel 39 and the disk 16.
Introduce butterfly nut 40 into the fastener of the
table 38 and place the 4 holes of the area 53 of
the table onto the 4 locations of the support
thereof.
8. Level the table and tighten the 2 butterfly nuts 40
and tighten the 4 fastening screws of the area 53
so as to fasten the table.
10.Fastening for working
Whenever possible, the work piece shall be
fastened in such a manner that there is no
intervention by hand. During cutting work piece,
hold the work piece stably against the support.
Always use the standard pusher 54 as included in
the equipment to push the work piece. All models
are prepared for mounting vertical and horizontal
clamps allowing fastening the work piece in a safe
manner. To avoid deformation of the work pieces
during fastening, it is recommended to use wooden
profiles that are easily adaptable to the movable
jaws of the clamps. Clamps are safe, can be taken
out easily and leave the work surface totally clear.
To cut long work pieces under safe conditions it is
essential to fasten them using additional supports.
11.Limits on the size of the work
pieces
Working limits for all models included in
this manual.